Zhongming LI
,
Mingbo YANG
,
Rui HUANG
,
Ai LU
,
Jianmin FENG
材料科学技术（英文）
In-situ composites based on dispersed poly (ethylene terephthalate) (PET) or polyamide (PA), and continuous polyethylene (PE) were prepared through a single screw extruder of Haake rheometer system with a rod-die relatively small in diameter. The extrudate was drawn at a drawing ratio of 3.1, and then quickly cooled in cold water. The specimens were obtained by injection molding at processing temperatures less than 190°C, far below the melting temperature of PET (265°C) and PA (230°C), which can maintain the solid state of PET and PA microfiber phase in the composites. Morphological observation with scanning electron microscopy (SEM) indicated that PET and PA can more or less form in-situ microfibers at compositions studied (0~20 wt pct PET or PA), and especially, PET and PA were almost deformed into fibers at the concentration of 15 wt pct. Tensile strength and modulus of the blends reinforced by PET or PA microfibers showed to be increased from the tensile test results. The most noticeable improvement of the tensile properties occurred at 15 wt pct of PET in PET/PE system, corresponding to the highest microfiber content, where the tensile strength reached 32.5 MPa, whereas only 19.5 Mpa for the pure PE.
关键词:
In-situ composite
,
null
,
null
,
null
张贺新
,
Jae-Hyeong Park
,
Young-Kwon Moon
,
Eun-Bin Ko
,
Dong-ho Lee
,
胡雁鸣
,
张学全
,
Keun-Byoung Yoon
催化学报
doi:10.1016/S1872-2067(16)62559-7
石墨烯自2004年发现以来,由于其独一无二的优异性迅速成为科学家们的研究热点.由于石墨烯具有极其优异的电学、力学和热学等性能,因此被广泛应用于高性能聚合物基复合材料的制备.众所周知,纳米填料在聚合物中的分散状态以及与基体间的界面作用是构筑高性能聚合物纳米复合材料的关键因素.由于石墨烯极易团聚,难以通过传统的熔融共混法制备均匀分散的石墨烯增强-聚烯烃纳米复合材料.另一方面,聚烯烃通常需要在较高温度下才能溶于部分有毒溶剂(如:三氯苯和二甲苯等),因此溶液共混法也不适用于聚烯烃-石墨烯纳米复合材料的制备.有鉴于此,本文开发了一种共沉积法制备石墨烯/二氯化镁负载钛系齐格勒-纳塔催化剂的路线.通过原位聚合直接制备出石墨烯均匀分散的聚烯烃/石墨烯纳米复合材料.考察了石墨烯的加入量对催化剂形态及其催化乙烯聚合行为的影响.当石墨烯加入量较低时,多个石墨烯片被包裹于较大的催化剂粒子中.随着石墨烯加入量的增加,催化剂趋向于在石墨烯表面聚集.继续增加石墨烯量将导致石墨烯包裹催化剂粒子,降低过渡金属钛的负载效率.通过三乙基铝活化后,所制备的催化剂具有非常高的乙烯催化活性,所生成的聚乙烯/石墨烯纳米复合材料复制了催化剂的片状结构.同时,通过对所制备的聚乙烯/石墨烯纳米复合材料进行电子显微镜和X射线衍射分析可知,石墨烯均匀分散于聚乙烯基体中,并且没有任何团聚现象发生.该复合材料的热重分析表明,仅加入非常少量的石墨烯就可以使其具有比纯聚乙烯更高的热稳定性,当石墨烯加入量为0.66 wt%时,其5 wt%热分解温度较纯聚乙烯升高了54°C.同时,所制备聚乙烯/石墨烯纳米复合材料具有更优异的机械性能.因此,本研究提供了一个简单高效的高性能聚烯烃/石墨烯纳米复合材料的制备方法.
关键词:
齐格勒-纳塔催化剂
,
聚乙烯
,
石墨烯
,
纳米复合材料
,
原位聚合
