J.L. Li
,
K.F. Wang
,
J. Li
,
Z.M. Yao and W. Ke(Fushun Petroleum Institute
,
Fushun 113001
,
China)(Department of Chemical Engineering
,
Zhejiang University
,
Hangzhou 310027
,
China)(Institute of Corrosion and Protection of Metals
,
The Chinese Academy of Sciences
,
Shengyang 110015
,
China)
金属学报(英文版)
Influence of hydrogen attack on mechanical and fatigue properties of 1020, 15CrMo and 2.25Cr-1Mo steels has been studied, which were exposed to gaseous hydrogen at pressure of 18MPa and 300-480℃ for up to 480h. The results of fatigue test showed that hydrogen attack (HA) resulted in an obvious change in fatigue properties of 1020 and 15CrMo steels, however, 2.25Cr-1Mo steel showed a lower susceptibility to hydrogen attack due to the addition of Cr and Mo. Fatigue crack behaviour for 1020 steel is attributed to hydrogen attack damage and the crack closure induced by the rough cracking surface, which lead to a valley on △Kth～HA% plot. The change in the fatigue behaviour of 15CrMo steel is possibly caused by severe surface decarburization.
关键词:
hydrogen attack
,
null
,
null
,
null
Z.L. Tian
,
Y.Q. Lai
,
J. Li
,
null
,
null
,
null
,
null
,
null
金属学报(英文版)
(Cu-Ni)/(10NiO-90NiFe2O4) cermet inert anodes containing metal Cu-Ni 0, 5, 10, 15 and 20 wt% were prepared and their corrosion behavior in Na3AlF6-Al2O3 melts was investigated. The results indicate that the content of metal Cu-Ni has little effect on the steady-state concentration of Ni in electrolyte, the steady-state concentration of Fe decreases from 304ppm to 168ppm and that of Cu increases from 21ppm to 71ppm with the content of metal Cu-Ni increasing from 0 to 20 wt%. Post-examination shows that metallic phase Cu-Ni is corroded preferentially during electrolysis and many pores are left at the anode surface. Considering the corrosion resistance and electrical conductivity, the cermet containing metal Cu-Ni 5 wt% behaves best among NiO-NiFe2O4 based cermet anodes examined, and should be further studied.
关键词:
aluminum electrolysis
,
null
,
null
,
null
Y.P. Ma
,
J. Li
金属学报(英文版)
The corrosion resistance of pure magnesium with surface alloying layer obtained by a solid diffusion alloying technique has been analyzed. To establish the optimum treatment time, the experiments were performed at 480℃ for different solid diffusion time (8, 16, and 24h). The diffusion interaction effectiveness between Zn, Al mix powder and the sample surface, depending on the treatment time for diffusion at given temperatures, has an obvious influence on corrosion resistance and corrosion mechanism. Corrosion properties were studied using the constant immersion test (in 3.0% NaCl solution, temperature is (28±1)℃, and time is 96h). Optical microscopy (OM) and EDS (energy dispersive spectrum) composition analysis were used to examine the cross-sectional microstructural characteristics of alloyed layer of treated samples. It is shown that in comparison with the untreated samples, the treated ones possess a better corrosion resistance. The Al5Mg11Zn4 phase, which formed as a continuous phase due to the diffusion of Al, Zn, and Mg elements and subsequent interaction on the outermost layer of diffusion alloying zones (especially the samples treated for 24h at 480℃), was inert to the chloride solution compared with pure magnesium and acted as a corrosion barrier, and therefore the best corrosion resistance was obtained. This protective action of Al5Mg11Zn4 phase was found to change with its amount, which was controlled by the diffusion time at given temperature. It was concluded that the continuous Al5Mg11Zn4 phase (WP-zone) of the reacted layer in pure magnesium was beneficial from the point of view of corrosion resistance.
关键词:
Pure magnesium
,
null
,
null
X.P. Li
,
J. Li
,
Y.Q. Lai
,
H.Q. Zhao
,
Y.X. Liu
金属学报(英文版)
A 2D full cell thermo-electric model of 160kA drained cell was set up using finite
element code to calculate its freeze profile, then the drained cell model was modified
according to the freeze profile computed and its heat balance was calculated. Compared
with that of a 160kA conventional Hall-Heroult cell (H-H cell), though the melts volume of the drained cell reduced greatly, the whole heat loss from it didn't drop down
apparently, and an analysis was presented in the paper. On the other hand, the anode-
cathode distance (ACD) of a drained cell was much less than that of a H-H cell, so
the voltage drop on it and heat produced decreased too, steps should be taken to keep
a workable heat balance on a drained cell.
关键词:
drained cell
,
null
,
null
X.C. Chen
,
Y.X. Liu
,
J. Li
金属学报(英文版)
An improved thermal decomposition method is used to prepare modified titanium base anode. Some researches have been carried out to learn about the oxygen evolution properties of RuMn, RuCo, RuCe and RuEu etc. in H2SO4 solution and their effect on the electrooxidation of methanol if added into the catalytic layers of Pt/Ti electrodes. The result indicates that the Pt/Ti electrodes containing RuMn, RuCo and RuEu etc. metal oxide catalysts with the powerful evolution property exhibit a higher electro-catalytic activity towards methanol electrooxidation than Pt/Ti electrodes without composite metal oxide catalysts.
关键词:
direct methanol fuel cell
,
null
,
null
,
null
