ZHOU Qingyue WANG Shuqing SHAO Yangdao NIE Shufan ZHOU Zhenguo China Academy of Railway Sciences
,
Beijing
金属学报(英文版)
A comparative investigation was carried out of the routine mechanical properties,fracture toughness,microstructure and hardness of slack-quenched rails containing different carbon contents.After the rails slack-quenched,their strength and toughness,together with ductility, are obviously improved,and the higher the quench hardening is,the more the resistance to wear and shell will be.Discussion was also made of the reason for this improvement and of the effect of carbon content and quench hardening on the properties of rails in combination with the rail-laying trial.
关键词:
carbon content
,
null
,
null
B.W. Wang
,
H. Shen
金属学报(英文版)
Ni-Cr System solar selective thin solid films were prepared by d.c. magnetron reactivesputtering under the atmosphere of O2 and N2. Ni-Cr alloy was chosen as targetmaterial and copper sheets as substrate. Using SEM, Spectrophotometer and Talystepto analyze the relations between the selective characteristic and the structure, theformation and the thickness of the thin films. The aim is to obtain good solar selectivethin films with high absorptance and low emittance, which is applied to flat plate solarheat collectors.
关键词:
solar selective thin film
,
null
,
null
,
null
CUI Juan
,
LIU Yazheng
,
PAN Hui
,
GAO Lifeng
钢铁研究学报(英文版)
The microsturctural transformation of austenite grain, pearlite interlamellar spacing, and lamellar cementite thickness of spring steel 60Si2MnA for railway were studied in the hotrolled and reheated states. Furthermore, the effect of microstructural characterization on its final mechanical properties was discussed. The results showed that as far as 60Si2MnA, the pearlite interlamellar spacing determined the hardness, whereas, the austenite grain determined the toughness. Compared with microstructure and mechanical properties in the hotrolled state, after reheating treatment at 950 ℃, its average grain sizes are apparently fine and the pearlite interlamellar spacing and lamellar cementite thickness coarsen to some extent, but both hardness and impact toughness increase to HRC 48 and 85 J, respectively. In the course of making spring, the optimum reheating austenitizing temperature for the 60Si2MnA steel is 950 ℃.
关键词:
austenitizing temperature;austenite grain;pearlite interlamellar spacing;hardness;toughness
Journal of Physics and Chemistry of Solids
The layered ternary ceramics Ti3SiC2 and Ti3AlC2 are isostructural and can form Ti3Si1-xAlxC2 solid solutions combining the advanced properties of both compounds [H.B. Zhang, Y.C. Zhou, Y.W. Bao, M.S. Li, Improving the oxidation resistance of Ti3SiC2 by forming a Ti3Si0.90Al0.1C2 solid solution, Acta Mater. 52 (2004) 3631-3637; E.D. Wu, J.Y. Wang, H.B. Zhang, Y.C. Zhou, K. Sun, Y.J. Xue, Neutron diffraction studies of Ti3Si0.9Al0.1C2 compound, Mater. Lett. 59 (2005) 2715-2719; J.Y. Wang, Y.C. Zhou, First-principles study of equilibrium properties and electronic structure of Ti3Si0.75Al0.25C2 solid solution, J. Phys.: Condens. Matter 15 (2003) 5959-5968; Y.C. Zhou, J.X. Chen, J.Y. Wang, Strengthening of Ti3AlC2 by incorporation of Si to form Ti3Al1-xSixC2 solid solutions, Acta. Mater. 54 (2006) 1317-1322]. In the present work, the solid solutions of Ti3Si1-xAlxC2 (x = 0, 0.25, 0.33, 0.5, 0.67, 0.75, 1) are investigated by first-principle calculations based on pseudo-potential plan-wave method within the density functional theory framework. The results show that as Al content increases in the solid solution, all the bonds have weakened to certain extents, which lead to an unstable structure both energetically and geometrically. The calculated results are compared and discussed with the reported data for the Ti3Si1-xAlxC2 solid solutions. (c) 2007 Elsevier Ltd. All rights reserved.
关键词:
ceramics;ab initio calculations;electronic structure;electrical;conductivity;oxidation behavior;mechanical-properties;ti3sic2;temperature;ti3alc2;air;si
LIANG Yong LI Ruiguo Institute of Metal Research
,
Academia Sinica
,
Shenyang 110015
,
ChinaInstitute of Corrosion and Protection of Metals
,
Aademia Sinica
,
Shenyang
,
110015
,
China
材料科学技术（英文）
Recent advances in laser coating technology including laser cladding,laser surface alloying and laser vapour deposition in China are reviewed in this paper.
关键词:
laser
,
null
,
null
,
null
,
null
新型炭材料
The 2011 Annual World Conference on Carbon (Carbon 2011) was held in Shanghai, China, during 24-29 July, 2011. This conference was hosted jointly by East China University of Science and Technology, University of Shanghai for Science and Technology, and Institute of Coal Chemistry Chinese Academy of Sciences. About 800 attendees from 42 countries/regions participated in this conference, and 797 papers were accepted for presentation, including 5 plenary lectures, 42 keynote lectures, 280 oral presentations, and 470 posters, involving 10 topics: graphene; nanocarbon, carbon for energy storage and conversion, porous carbon and adsorption, carbon fiber and composites, precursor/carbonization and graphitization, computation and modeling, bio-carbon and safety, novel experimental techniques and characterization, bulk carbon and industrial applications. Research and development of nanocarbons are quite active and in particular, graphene received tremendous interest. Rapid progress has also been made on the electrochemical properties, energy conversion and energy storage applications of carbon materials.
关键词:
