Nuclear Engineering and Design
Liquid droplet erosion (LDE), which often occurs in bellows made of nickel-based alloys, threatens the security operation of the nuclear power plant. As the candidate materials of the bellows, Inconel 600 and Inconel 625 were both tested for resistance to cavitation erosion (CE) and jet impingement erosion (JIE) through vibratory cavitation equipment and a jet apparatus for erosion-corrosion. Cumulative mass loss vs. exposure time was used to evaluate the erosion rate of the two alloys. The surface and cross-sectional morphologies before and after the erosion tests were observed by scanning electron microscopy (SEM), the inclusions were analyzed by an energy dispersive spectroscopy (EDS), and the surface roughness was also measured by surface roughness tester to illustrate the evolution of erosion process. The results show that the cumulative mass loss of CE of Inconel 625 is about 1/6 that of Inconel 600 and the CE incubation period of the Inconel 625 is 4 times as long as that of the Inconel 600. The micro-morphology evolution of CE process illustrates that the twinning and hardness of the Inconel 625 plays a significant role in CE. In addition, the cumulative mass loss of JIE of Inconel 625 is about 2/3 that of Inconel 600 at impacting angle of 90 degrees, and almost equal to that of the Inconel 600 at impacting angle of 30 degrees. Overall, the resistance to CE and JIE of Inconel 625 is much superior to that of Inconel 600. (C) 2010 Elsevier By. All rights reserved.
关键词:
stress-corrosion cracking;aluminide intermetallic alloys;high-purity;water;mechanical-properties;crevice corrosion;solid particles;wear;behavior;microstructure;deformation;steam
Physical Review B
In order to understand the unusually large value of zero-field splitting D for the axial Fe3+ center in a KTaO3 crystal, Zhou made two assumptions in his recent report [Phys. Rev. B 42, 917 (1990)]. In this Comment we will show that his assumption II is qualitatively reasonable, whereas assumption I is unnecessary and doubtful.
关键词:
electric-field;srcl2
Nuclear Engineering and Design
A composite coating was deposited on Inconel 600 substrate by cold spray method using pure Ni powder (60 wt.%) blended with alpha-Al(2)O(3) (40 wt.%) as feedstock. It is expected to be applied to repair the bellows eroded by the liquid droplet erosion (LDE). Microstructure of the coating was observed using optical microscope (OM) and scanning electron microscopy (SEM). Microhardness of the coating was determined by Vickers hardness tester. Cavitation erosion (CE) experiments were carried out in the distilled water. Jet impingement erosion (JIE) experiments were performed in slurry containing 1 wt.% quartz particle with the flow velocity of 15 m/s at impingement angles of 30 degrees, 60 degrees and 90 degrees, respectively. Cumulative mass loss vs. testing time was used to evaluate the erosion rate of the coating. The erosion mechanism was analyzed by OM, SEM, X-ray diffraction (XRD) and the microhardness measurement. The results show that the composite coating has compact microstructure and relatively high hardness. The resistance to CE of the coating is not as good as that of Inconel 600 substrate due to the weak bonds of the Al(2)O(3) particles. However, the results of the JIE test indicate that the slurry erosion resistance of the coating is better than that of Inconel 600 at the impact angles of 30 degrees and 60 degrees, but not at the normal impact angle. (C) 2011 Elsevier B.V. All rights reserved.
关键词:
large powder particles;composite coatings;slurry erosion;kinetic;spray;liquid impact;alloy;microstructure;steels;deposition;resistance
Journal of Physics and Chemistry of Solids
The layered ternary ceramics Ti3SiC2 and Ti3AlC2 are isostructural and can form Ti3Si1-xAlxC2 solid solutions combining the advanced properties of both compounds [H.B. Zhang, Y.C. Zhou, Y.W. Bao, M.S. Li, Improving the oxidation resistance of Ti3SiC2 by forming a Ti3Si0.90Al0.1C2 solid solution, Acta Mater. 52 (2004) 3631-3637; E.D. Wu, J.Y. Wang, H.B. Zhang, Y.C. Zhou, K. Sun, Y.J. Xue, Neutron diffraction studies of Ti3Si0.9Al0.1C2 compound, Mater. Lett. 59 (2005) 2715-2719; J.Y. Wang, Y.C. Zhou, First-principles study of equilibrium properties and electronic structure of Ti3Si0.75Al0.25C2 solid solution, J. Phys.: Condens. Matter 15 (2003) 5959-5968; Y.C. Zhou, J.X. Chen, J.Y. Wang, Strengthening of Ti3AlC2 by incorporation of Si to form Ti3Al1-xSixC2 solid solutions, Acta. Mater. 54 (2006) 1317-1322]. In the present work, the solid solutions of Ti3Si1-xAlxC2 (x = 0, 0.25, 0.33, 0.5, 0.67, 0.75, 1) are investigated by first-principle calculations based on pseudo-potential plan-wave method within the density functional theory framework. The results show that as Al content increases in the solid solution, all the bonds have weakened to certain extents, which lead to an unstable structure both energetically and geometrically. The calculated results are compared and discussed with the reported data for the Ti3Si1-xAlxC2 solid solutions. (c) 2007 Elsevier Ltd. All rights reserved.
关键词:
ceramics;ab initio calculations;electronic structure;electrical;conductivity;oxidation behavior;mechanical-properties;ti3sic2;temperature;ti3alc2;air;si
ZHOU Jiankun LIU Xianghuai CHEN Youshan WANG Xi ZHENG Zhihong HUANG Wei ZOU Shichang Shanghai Institute of Metallurgy
,
Academia Sinica
,
Shanghai
,
China
金属学报(英文版)
The TiN films were synthesized with an alternate process of depositing titanium from a E-gun evaporation source and 40 keV N~+ bombarding onto the target.It is shown from the composi- tion analysis and structure investigations using RBS,AES,TEM,XPS and X-ray diffraction spectrum that the formed fihns are mainly composed of TiN phase with grain size of 30—40 nm and without preferred orientation,the nitrogen content in the film is much less than that in case without N~+ bombarding,and an intermixed region about 40 nm thick exists between the film and the substrate.The films exhibt high microhardness and low friction. ZHOU Jiankun,Ion Beam Laboratory,Shanghai Institute of Metallurgy,Academia Sinica, Shanghai 200050,China
关键词:
TiN film
,
null
涂娜
,
江向平
,
李小红
,
傅小龙
,
杨帆
人工晶体学报
采用传统固相法制备了(1-x)Bi4Ti3 O12-xSrBi2 Nb2 O9(BIT-SBN,x=0,0.025,0.050,0.100,0.150,0.200)铋层状无铅压电陶瓷.系统研究了SrBi2 Nb2 O9掺杂对Bi4Ti3 O12基陶瓷物相结构、微观结构以及jie电性能的影响.结果表明:所有陶瓷样品均为单一的铋层状结构;当SBN掺量为0.100时,样品具有最佳的电性能:d33=21 pC/N,相对密度ρ =98.1％,机电耦合系数kp=8.26％,εr=220,介电损耗tanδ =0.29％,剩余极化强度Pr=9.128 μC/cm2,Tc=594℃.同时,SBN的引入增强了样品的抗老化性和热稳定性.
关键词:
Bi4Ti3O12
,
SrBi2Nb2O9
,
铋层状
,
铁电陶瓷
,
介电性能
Physical Review B
The assignment of the absorption spectrum of Y3Fe5O12 (YIG) made by Scott et al. [Phys. Rev. B 10, 971 (1974)] is shown to be incorrect and a new one is made by diagonalizing the complete cubic crystal-field matrices for d5 ions, involving spin-orbit interaction, given by Zhou et al. [Phys. Rev. B 44, 7499 (1991)]. The Racah parameters B and C, the crystal-field parameter Dq, and the spin-orbit coupling coefficient zeta are determined (in units of cm-1) as B = 783.3(530), C = 2928(3220), Dq = 1336(1300), zeta = 395 for octahedral Fe3+, and B = 606.1(705), C = 2696(2730), Dq = -1117.3(560), zeta = 335 for tetrahedral Fe3+, where the numerals in parentheses are the values adopted by Scott et al. Furthermore, the cubic zero-field splitting parameter a of Fe3+ in YIG is calculated to be a(oct) = 156 X 10(-4) cm-1 and a(tet) = 58.6 X 10(-4) cm-1. The value for a(oct) differs from the value of 189 X 10(-4) cm-1 found for Fe3+ in Y3Ga5O12:Fe3+. These results support speculations made by Geschwind [Phys. Rev. 121, 363 (1961)].
关键词:
fe3+;mn2+
刘守平
,
周上祺
,
王佳眉
,
任勤
腐蚀学报（英文）
用金相显微镜、扫描电镜、X射线衍射仪和X射线能谱仪对天然气井油管悬挂器腐蚀失效进行了检测分析，并对天然气井油管悬挂器用35CrMo钢进行了盐雾试验，结果表明，天然气中的水和CO2是引起腐蚀的主要介质，腐蚀产物主要是FeCO3，高速天然气冲刷和钢中的非金属夹杂加剧了腐蚀的速度.
CORROSION FAILURE ANALYSIS OF AN OIL TUBE USED IN NATURAL GAS WELL
LIU Shou-ping,ZHOU Shang-qi,WANG Jia-mei,REN Qin
Chongqing University
A failed oil tube used in natural gas well was examined by optical microscope,scanning electron microscope ,X-ray diffractometer and X-ray spectrometer.Corrosion behavior of 35CrMo steel samples of the oil tube were investigated by means of salt spray tests in the laboratory.The results show that CO2 and H2O are primary factors in the corrosion of oil tube.The corrosion product is FeCO3,non-metallic inclusions in the steel and erosion of natural gas fluid played an important role in accelerating the corrosion.
oil tube;
natural gas well；
35CrMo steel；
failure analysis；
corrosion
关键词:
悬挂器
,
null
,
null
,
null
章春香
,
殷海荣
,
刘立营
,
唐保军
材料导报
采用Zhou W C提出的玻璃形成区研究方法探索了铽硼硅酸盐磁光玻璃形成区域范围,采用魔角核磁共振谱仪(MAS NMR)和示差扫描量热仪(DSC)对玻璃结构和特征温度能进行了表征,研究了Tb2O3和Al2O3对玻璃形成能力和玻璃结构的影响,同时引入玻璃析晶参数β讨论玻璃热稳定性.结果表明:Tb2O3的掺入量受玻璃形成区域的限制,在Tb2O3含量为30%(摩尔分数)时以及Al2O3含量为25%(摩尔分数)时玻璃形成能力较强;铽铝硼硅酸盐玻璃结构中硼氧多面体和铝氧多面体主要以四配位的[BO4]和[AlO4]形式存在,仍存在少量三配位的[BO3]和五配位的[AlO5];Tb2O3含量为30%(摩尔分数)的玻璃β值较大,热稳定性能较好.
关键词:
铝硼硅酸盐玻璃
,
磁光玻璃
,
玻璃成形区
,
氧化铽
,
稀土
