ZHAO Xin
,
YANG Xiaoling
,
JING Tianfu
钢铁研究学报(英文版)
The hot deformation characteristics of ductile iron are studied in the temperature range of 973 to 1273K and strain rate range of 0001 to 1 s-1 by using hot compression tests. Processing maps for hot working are developed on the basis of the variations of efficiency of power dissipation with temperature and strain rate. The results reveal that the flow stress of ductile iron is sensitive to strain rate. In the processing map under strain of 07, a domain is centered at 1273 K and 1 s-1, and the maximum efficiency is more than 36%. According to the maps, the zone with the temperature range of 1173 to 1273 K and strain rate range of 01 to 1 s-1 may be considered as the optimum region for hot working.
关键词:
ductile iron; processing map; hot working
ZHAO Xin
,
YANG Xiao-ling
,
JING Tian-fu
钢铁研究学报(英文版)
In order to investigate the effect of initial microstructure on warm deformation behavior, some specimens of 45 steel were annealed and some quenched. Then the specimens were isothermally compressed on a Gleeble 3500 machine. The deformation temperature range was 550 to 700 ℃ and the strain rate range was 0.001 to 0.1 s-1. An optical microscope (OM) and a transmission electron microscope (TEM) were used to study the microstructures. The results show that the microstructure of annealed specimens is ferrite and pearlite and that of quenched specimens is martensite. The flow stress of quenched specimens is higher than that of annealed ones at 550 ℃ when strain rates are greater than 0.001 s-1. However, at 600 to 700 ℃ and strain rate of 0.001 s-1, the whole flow curves of quenched specimens are below that of annealed ones. Under the rest conditions, the flow stress of quenched specimens is higher at the beginning of compression and then the opposite is true after the strain is greater than a critical value. The microstructure examination proves that the tempering and dynamic recrystallization easily occur in the specimens with martensite during warm compression, which results in the above phenomena.
关键词:
warm deformation
,
flow stress
,
steel
,
microstructure
常永勤
,
介万奇
,
郭喜平
,
陈福义
,
安卫军
功能材料
研究了ACRT-B法生长的Mn0.1Cd0.9In2Te4晶体中界面的形状和各组元沿轴向的分布规律及其分凝因数.发现结晶界面为椭球形;采用理想配比生长MnxCd1-xIn2Te4晶体,其4种组元并不按(Mn,Cd):In:Te=1:2:4比例结晶,而是要重新分布;通过数学方法处理实验数据得到Mn,Cd和In的分凝因数在α相区分别为1.286、1.9257和0.7294,在β相区则分别为1.12、1.055和0.985.
关键词:
ACRT-B法
,
MnxCd1-x In2Te4
,
界面
,
分凝因数
常永勤
,
安卫军
,
郭喜平
,
介万奇
无机材料学报
采用Bridgman法生长了x为0.1,0.22和0.4的四元稀磁半导体化合物MnxCd1-xIn2Te4晶体.研究了三根晶体中相的形貌、结构、成分和Mn0.1Cd0.9In2Te4晶体中各组元沿轴向和径向的成分分布.晶体生长初始端的组织为α+β+β1,随着生长的进行,形成β相的单相区.在晶锭末端,形成In2Te3类面心立方结构化合物.组分x增大后,MnxCd1-xIn2Te4晶体的吸收边向短波方向移动,禁带宽度则线性增大.磁化率测量结果表明:晶体在高温区的x-1-T曲线服从居里-外斯定律,在低温区(<50K)则表现出顺磁增强现象.
关键词:
MnxCd1-xIn2Te4
,
compositional distribution
,
infrared transmission spectra
,
mag- netic susceptibility
常永勤
,
安卫军
,
郭喜平
,
介万奇
无机材料学报
doi:10.3321/j.issn:1000-324X.2003.02.004
采用Bridgman法生长了x为0.1,0.22和0.4的四元稀磁半导体化合物MnxCd1-xIn2Te4晶体.研究了三根晶体中相的形貌、结构、成分和Mno.1Cd0.9In2Te4晶体中各组元沿轴向和径向的成分分布.晶体生长初始端的组织为α+β+β1,随着生长的进行,形成β相的单相区.在晶锭末端,形成In2Te3类面心立方结构化合物.组分x增大后,MnxCd1-xIn2Te4晶体的吸收边向短波方向移动,禁带宽度则线性增大.磁化率测量结果表明:晶体在高温区的x-1-T曲线服从居里一外斯定律,在低温区(＜50K)则表现出顺磁增强现象.
关键词:
MnxCd1-xIn2Te4
,
成分偏析
,
红外透射光谱
,
磁化率
常永勤
,
安卫军
,
郭喜平
,
介万奇
功能材料
采用Bridgman法生长四元稀磁化合物半导体Mn0.22Cd0.78In2Te4晶体.当晶体生长到预定长度时,淬火得到固液界面.采用光学显微镜、扫描电镜、X射线衍射仪、ISIS能谱仪以及Leica定量金相分析仪研究了晶体中出现的界面形态、相的形貌和数量以及沿生长方向的相析出规律,并进行了相成分分析.研究发现,淬火得到的Mn0.22 Cd0.78In2Te4晶体中存在两个界面,其中一个为固液相变界面,另一个为由α+β两相区发展到单相β区时的转变界面,二者相对于生长初始端均为凹形;α+β两相区中,β相以条状、花状和近似圆片状形式存在,其中条状β相多分布在晶界处;越接近生长初始端,花状和近似圆片状β相越小,条状β相越细,它们的含量越少;X射线衍射图谱表明,β相为黄铜矿结构,α相为面心立方结构.
关键词:
MnxCd1-xIn2Te4
,
相变界面
,
β相
,
X射线衍射图谱
Farook ADAM*, Kei Lin SEK
催化学报
doi:10.1016/S1872-2067(11)60453-1
Indium incorporated silica samples with different indium contents were synthesized using a template free sol-gel method. The silica used was extracted from rice husk (RH) and the resulting catalyst was labeled as RH-xIn (x=5%,10%,15%, and 20%). From the N2 adsorption analysis the presence of type IV isotherm in RH-blank and RH-xIn indicated the mesoporous nature of the catalysts. In the XRD pattern, a broad band at ca.2θ=25° was observed for all the catalysts which showed them to be amorphous. TEM micrographs revealed that the material is composed of nanoparticles. Friedel-Craft benzoylation of toluene was carried out using the RH-xIn catalyst. The optimum conditions for the benzoylation of toluene were determined and at 373 K,100%conversion and 89%selectivity for the para-product (i.e.4-methylbenzophenone) were obtained.
关键词:
rice husk
,
sol-gel
,
indium
,
Friedel-Craft benzoylation
,
Toluene
中国腐蚀与防护学报
N。1Atmospheric Corrosivlty for Steels………………………………………………… .LIANG Caideng HO[I i。-tat（6）Caustic Stress Corrosion Cr。king of Alloy 800 Part 2.The Effect of Thiosul执e……………………………………… KONG De-sheng YANG Wu ZHAO Guo-zheng HUANG De.ltL。ZHANG Yu。。he CHEN She。g-bac（13）SERS slid E16CttOCh6iniC81 Stlldy Of Illhibit1Oli M6ch＆tllsth Of ThlollY68 Oil ITOll ID H....
关键词:
