XU Ji-fang
,
ZHANG Jie-yu
,
JIE Chang
,
TANG Lei
,
CHOU Kuo-chih
钢铁研究学报(英文版)
The densities of the selected quaternary CaO-MgO-Al2O3-SiO2 slag with low silica were measured by the Archimedean method in a wide temperature range from 1773 to 1873 K. Nine different slag compositions were chosen based on three different levels of CaO content and three different levels of SiO2 content. wMgO was equal to 7.0%. wCaO were varied from 40.04% to 50.64%, for wSiO2=10.25%-20.70%. The effects of temperature, SiO2 content and optical basicity were studied. It is shown that density decreases approximately linearly with an increase in temperature. Under the same CaO content, the density decreases with increasing of SiO2 content, and increases with optical basicity increasing. Based on the experimental data as the boundary of the homogenous phase region predicated by FACTSAGE software, the mass triangle model is used to calculate the density of selected limited homogenous phase region. The results showed that the mass triangle model works well.
关键词:
density
,
slag
,
low silica
,
optical basicity
,
model
中国腐蚀与防护学报
N。1Atmospheric Corrosivlty for Steels………………………………………………… .LIANG Caideng HO[I i。-tat(6)Caustic Stress Corrosion Cr。king of Alloy 800 Part 2.The Effect of Thiosul执e……………………………………… KONG De-sheng YANG Wu ZHAO Guo-zheng HUANG De.ltL。ZHANG Yu。。he CHEN She。g-bac(13)SERS slid E16CttOCh6iniC81 Stlldy Of Illhibit1Oli M6ch&tllsth Of ThlollY68 Oil ITOll ID H....
关键词:
Journal of Materials Research
The morphology of the dark and bright regions observed by transmission electron microscopy for the Zr(64.13)Cu(15.75)Ni(10.12)Al(10) bulk metallic glass strongly depends on the ion beam parameters used for ion milling. This indicates that the ion beam could introduce surface fluctuation to metallic glasses during ion milling.
关键词:
room-temperature
Nuclear Engineering and Design
Liquid droplet erosion (LDE), which often occurs in bellows made of nickel-based alloys, threatens the security operation of the nuclear power plant. As the candidate materials of the bellows, Inconel 600 and Inconel 625 were both tested for resistance to cavitation erosion (CE) and jet impingement erosion (JIE) through vibratory cavitation equipment and a jet apparatus for erosion-corrosion. Cumulative mass loss vs. exposure time was used to evaluate the erosion rate of the two alloys. The surface and cross-sectional morphologies before and after the erosion tests were observed by scanning electron microscopy (SEM), the inclusions were analyzed by an energy dispersive spectroscopy (EDS), and the surface roughness was also measured by surface roughness tester to illustrate the evolution of erosion process. The results show that the cumulative mass loss of CE of Inconel 625 is about 1/6 that of Inconel 600 and the CE incubation period of the Inconel 625 is 4 times as long as that of the Inconel 600. The micro-morphology evolution of CE process illustrates that the twinning and hardness of the Inconel 625 plays a significant role in CE. In addition, the cumulative mass loss of JIE of Inconel 625 is about 2/3 that of Inconel 600 at impacting angle of 90 degrees, and almost equal to that of the Inconel 600 at impacting angle of 30 degrees. Overall, the resistance to CE and JIE of Inconel 625 is much superior to that of Inconel 600. (C) 2010 Elsevier By. All rights reserved.
关键词:
stress-corrosion cracking;aluminide intermetallic alloys;high-purity;water;mechanical-properties;crevice corrosion;solid particles;wear;behavior;microstructure;deformation;steam
Nuclear Engineering and Design
A composite coating was deposited on Inconel 600 substrate by cold spray method using pure Ni powder (60 wt.%) blended with alpha-Al(2)O(3) (40 wt.%) as feedstock. It is expected to be applied to repair the bellows eroded by the liquid droplet erosion (LDE). Microstructure of the coating was observed using optical microscope (OM) and scanning electron microscopy (SEM). Microhardness of the coating was determined by Vickers hardness tester. Cavitation erosion (CE) experiments were carried out in the distilled water. Jet impingement erosion (JIE) experiments were performed in slurry containing 1 wt.% quartz particle with the flow velocity of 15 m/s at impingement angles of 30 degrees, 60 degrees and 90 degrees, respectively. Cumulative mass loss vs. testing time was used to evaluate the erosion rate of the coating. The erosion mechanism was analyzed by OM, SEM, X-ray diffraction (XRD) and the microhardness measurement. The results show that the composite coating has compact microstructure and relatively high hardness. The resistance to CE of the coating is not as good as that of Inconel 600 substrate due to the weak bonds of the Al(2)O(3) particles. However, the results of the JIE test indicate that the slurry erosion resistance of the coating is better than that of Inconel 600 at the impact angles of 30 degrees and 60 degrees, but not at the normal impact angle. (C) 2011 Elsevier B.V. All rights reserved.
关键词:
large powder particles;composite coatings;slurry erosion;kinetic;spray;liquid impact;alloy;microstructure;steels;deposition;resistance