宋育来
,
陈吉清
,
陈邦文
,
刘静
,
刘志勇
,
胡敏
钢铁研究
研究了集装箱用SM490YA钢板的力学性能、工艺性能、微观组织结构等.采用气体保护焊对钢板进行焊接性能试验评价,并对钢的强韧化机理进行初步探讨.结果表明,SM490YA钢板不仅性能稳定,不存在明显的各向异性,易于成型,而且钢板焊接性能优良,是制造集装箱的理想钢板.
关键词:
集装箱钢
,
力学性能
,
工艺性能
,
焊接性能
,
微观组织
林元华
,
张中太
,
张枫
,
唐子龙
,
吕霄
,
郑子山
功能材料
利用SrCO3-A12O3-RE(NO3)3(RE:Eu,Dy)粉体为原料,加入少量酒精,进行预混合、球磨、干燥.将此混合粉体在还原气氛下高温烧成,最终制得不同发光性能的xSrO.yAl2O3:RE(RE:Eu,Dy)光致发光材料,并对其性能进行了研究.发光粉体的发射光谱表明,随着A12O3/SrO(摩尔比x)的增加,其相应粉体发射光谱的主峰位置(λE)逐渐向短波方向移动,符合λE=531.018-23.028X关系式.余辉衰减曲线表明,这些发光材料均具有一定的长余辉特性.从而说明只要控制一定的Al2O3/SrO比例,即可获得发光颜色为紫色到绿色的多种发光材料.对于其长余辉机制,认为是加入的Dy3+起到了陷阱能级的作用,它将部分空穴俘获,并在热扰动下,慢慢将空穴释放出来,并再次与介稳态Eu1+复合发光,从而达到延长余辉的作用.
关键词:
长余辉
,
发光材料
,
发射光谱
,
空穴
Nuclear Engineering and Design
Liquid droplet erosion (LDE), which often occurs in bellows made of nickel-based alloys, threatens the security operation of the nuclear power plant. As the candidate materials of the bellows, Inconel 600 and Inconel 625 were both tested for resistance to cavitation erosion (CE) and jet impingement erosion (JIE) through vibratory cavitation equipment and a jet apparatus for erosion-corrosion. Cumulative mass loss vs. exposure time was used to evaluate the erosion rate of the two alloys. The surface and cross-sectional morphologies before and after the erosion tests were observed by scanning electron microscopy (SEM), the inclusions were analyzed by an energy dispersive spectroscopy (EDS), and the surface roughness was also measured by surface roughness tester to illustrate the evolution of erosion process. The results show that the cumulative mass loss of CE of Inconel 625 is about 1/6 that of Inconel 600 and the CE incubation period of the Inconel 625 is 4 times as long as that of the Inconel 600. The micro-morphology evolution of CE process illustrates that the twinning and hardness of the Inconel 625 plays a significant role in CE. In addition, the cumulative mass loss of JIE of Inconel 625 is about 2/3 that of Inconel 600 at impacting angle of 90 degrees, and almost equal to that of the Inconel 600 at impacting angle of 30 degrees. Overall, the resistance to CE and JIE of Inconel 625 is much superior to that of Inconel 600. (C) 2010 Elsevier By. All rights reserved.
关键词:
stress-corrosion cracking;aluminide intermetallic alloys;high-purity;water;mechanical-properties;crevice corrosion;solid particles;wear;behavior;microstructure;deformation;steam
胡海龙
,
曾宇平
,
左开慧
,
夏咏锋
,
姚冬旭
无机材料学报
doi:10.15541/jim20140181
分别以Y2O3-Al2O3(YA)和Y2O3-MgO(YM)为烧结助剂，采用气压烧结工艺制备了Si3N4/SiC陶瓷，研究了两种不同的烧结助剂对陶瓷的力学和摩擦性能的影响。研究结果表明：添加不同种类的烧结助剂对制备陶瓷的相对密度、抗弯强度、断裂韧性、硬度、摩擦系数和磨损率影响很大；与添加烧结助剂YM相比较，添加烧结助剂YA的Si3N4/SiC陶瓷在烧结过程中表现出了更好的烧结性能，得到的陶瓷样品最终显示了更好的力学和摩擦性能，尤其是SiC添加量为20wt%的Si3N4/SiC陶瓷。这主要归因于烧结助剂YA的添加使Si3N4/SiC陶瓷呈现出了更高的相对密度，获得的晶粒长径比更小。
关键词:
Si3N4/SiC陶瓷
,
烧结助剂
,
抗弯强度
,
摩擦性能
Nuclear Engineering and Design
A composite coating was deposited on Inconel 600 substrate by cold spray method using pure Ni powder (60 wt.%) blended with alpha-Al(2)O(3) (40 wt.%) as feedstock. It is expected to be applied to repair the bellows eroded by the liquid droplet erosion (LDE). Microstructure of the coating was observed using optical microscope (OM) and scanning electron microscopy (SEM). Microhardness of the coating was determined by Vickers hardness tester. Cavitation erosion (CE) experiments were carried out in the distilled water. Jet impingement erosion (JIE) experiments were performed in slurry containing 1 wt.% quartz particle with the flow velocity of 15 m/s at impingement angles of 30 degrees, 60 degrees and 90 degrees, respectively. Cumulative mass loss vs. testing time was used to evaluate the erosion rate of the coating. The erosion mechanism was analyzed by OM, SEM, X-ray diffraction (XRD) and the microhardness measurement. The results show that the composite coating has compact microstructure and relatively high hardness. The resistance to CE of the coating is not as good as that of Inconel 600 substrate due to the weak bonds of the Al(2)O(3) particles. However, the results of the JIE test indicate that the slurry erosion resistance of the coating is better than that of Inconel 600 at the impact angles of 30 degrees and 60 degrees, but not at the normal impact angle. (C) 2011 Elsevier B.V. All rights reserved.
关键词:
large powder particles;composite coatings;slurry erosion;kinetic;spray;liquid impact;alloy;microstructure;steels;deposition;resistance
中国腐蚀与防护学报
N。1Atmospheric Corrosivlty for Steels………………………………………………… .LIANG Caideng HO[I i。-tat（6）Caustic Stress Corrosion Cr。king of Alloy 800 Part 2.The Effect of Thiosul执e……………………………………… KONG De-sheng YANG Wu ZHAO Guo-zheng HUANG De.ltL。ZHANG Yu。。he CHEN She。g-bac（13）SERS slid E16CttOCh6iniC81 Stlldy Of Illhibit1Oli M6ch＆tllsth Of ThlollY68 Oil ITOll ID H....
关键词:
