Y. Chen
金属学报(英文版)
The effects of finishing rolling temperature and coiling temperature on retained austen-ire were studied for hot-rolled transformation induced plasticity (TRIP) steels withdifferent carbon content. The experimental results showed that an appropriate volumefraction of retained austenite from 6% to 11% could be obtained according to the dif-ferent carbon content less than 0.20% by controlled finishing rolling and coiling forthe hot-rolled TRIP steels. It can be concluded that carbon content has a significanteffect on the fraction of retained austenite and coiling processing plays stronger roleon retaining austenite than fishing rolling processing.
关键词:
TRIP steel
,
null
,
null
Y. Chen
金属学报(英文版)
A hot-rolled deep drawing (HDD) steel with high r-value and uniform distribution of{ 111} texture in thickness was developed by hot rolling in ferrite region with lubricatingbetween the roller and the steel. The experimental results show that the carbon contentand finish rolling temperature have significant effects on beneficial texture {111}, andlubricating during hot rolling at low temperature in α-region makes the distributionof the texture uniform. Three basic requirements needed to meet for HDD steel wereconcluded by comparing different carbon contents and hot rolling processes.
关键词:
ultra low carbon
,
null
,
null
,
null
,
null
Y. Chen
,
X. Chen
,
Q.F. Wang
金属学报(英文版)
The systematic chemical compositions including common C, Si, Mn, Al, and micro- alloying elements of Ti and Nb were designed for high volume fraction of retained austenite as much as possible. The thermo-cycle experiments were conducted by using Gleeble 2000 thermo-dynamic test machine for finding the appropriate composition. The experimental results showed that chemical composition had a significant effect on retained austenite, and the appropriate compositions were determined for commercial production of TRIP steels.
关键词:
carbon content
,
null
,
null
,
null
,
null
李开明
,
李亚洲
,
冯维贵
,
林长
量子电子学报
doi:10.3969/j.issn.1007-5461.2007.05.014
采用非线性反馈控制,用附加了带参数的正弦项对Chen系统进行了有效的控制.随着参数k的逐渐增大,系统的动力学行为呈现出一系列的变化.数值研究结果表明:随控制参数的增大,驱动信号的强度渐大,混沌系统由混沌运动到周期轨道,最终到一相点.
关键词:
混沌
,
Chen系统
,
不动点
,
Lyapunov指数
,
反馈控制
马宏
,
彭晓东
,
谢卫东
腐蚀学报（英文）
利用对掺法熔铸镁合金AJ61+xY, 研究了合金中相的组成和分布及其在3.5%NaCl溶液中的腐蚀行为. 结果表明, 添加稀土Y使AJ61镁合金的晶粒明显细化,Mg17Al12 相的数量明显减少且由连续网状变成弥散颗粒状分布,沿晶界处生成耐蚀稀土相Al2Y、Al3Y, AJ61镁合金的耐腐蚀性得到明显改善. 耐腐蚀性顺序为:AJ61+1.5%Y>AJ61+2.0%Y>AJ61+1.0%Y>AJ61+0.5%Y.
关键词:
Mg-6Al-1Sr 镁合金
,
yttrium
,
microstructure
,
corrosion resistance
马宏
,
彭晓东
,
谢卫东
腐蚀学报（英文）
利用对掺法熔铸镁合金AJ61++xY,研究了合金中相的组成和分布及其在3.5%NaCl溶液中的腐蚀行为.结果表明,添加稀土Y使AJ61镁合金的晶粒明显细化,Mg17Al12相的数量明显减少且由连续网状变成弥散颗粒状分布,沿晶界处生成耐蚀稀土相Al2Y、Al3Y,AJ61镁合金的耐腐蚀性得到明显改善.耐腐蚀性顺序为:AJ61+1.5%Y＞AJ61+2.0%Y＞AJ61+1.0%Y＞AJ61+0.5%Y.
关键词:
Mg-6Al-1Sr镁合金
,
钇
,
显微组织
,
耐腐蚀
Yan NIU
,
Weitao WU and Chaoliu ZENG (State Key Lab. for Corrosion and Protection
,
Institute of Corrosion and Protection of Metals
,
Chinese Academy of Sciences
,
Shenyang 110015
,
China)F. Gesmundo and F. Viani (Instituto di Chimica
,
Facolta di Ingegneria
,
Un
材料科学技术（英文）
The corrosion of an Fe-based alloy containing 15 wt pct Y in H2-H2S mixtures under 10-3 Pa S2 was studied at 600~800℃ in an attempt to find materials with improved sulphidation resistance with respect to pure Fe. The presence of Y has been shown to be beneflcial, but not sufficient to the level expected. In fact, the alloy is able to form at all tested temperatures an external FeS layer, beneath which a zone containing a mixture of the two sulphides is also present. Thus,Fe can still diffuse through this region to form the outer FeS layer with non-negligible rate. The corrosion rate of Fe is considerably reduced by the Y addition. but the alloy corrodes still much more rapidly than Y. The sulphidation kinetics is generally rather irregular for both the pure metals, while the corrosion rate of the alloy decreases with time and tends to become parabolic after an initial period of 12~17 h. The sulphidation behaviour of the alloys is discussed by taking into account the presence of an intermetallic compound Fe17Y2 and the limited solubility of Y in Fe
关键词:
Journal of Materials Research
The morphology of the dark and bright regions observed by transmission electron microscopy for the Zr(64.13)Cu(15.75)Ni(10.12)Al(10) bulk metallic glass strongly depends on the ion beam parameters used for ion milling. This indicates that the ion beam could introduce surface fluctuation to metallic glasses during ion milling.
关键词:
room-temperature
Transactions of Nonferrous Metals Society of China
The influence of Zr and Y on the cast microstructure of a nickel-based superalloy was investigated by optical microscopy (OM), scanning electron microscopy(SEM), electron probe micro-analysis (EPMA) and X-ray diffraction (XRD). The gamma+gamma' eutectic volume in the superalloy rises notably with the increase of Zr or Y content. Meanwhile, the morphologies of primary MC carbides change from needle and platelet-like to blocky shape with increasing Zr and Y doped. The XRD results show that the primary MC carbide lattice constant increases with Zr and Y additions, and EPMA investigation shows that the platelet-like MC carbides contain primarily Nb and C, while those carbides in blocky shape have 39.2% Zr and 39.6% Nb in average,. These influences on the cast microstructure can be attributed to the atomic size effects of Zr and Y.
关键词:
yttrium;zirconium;carbides;nickel based superalloys;microstructure;solidification;carbide morphology;mechanical-properties;boron;ni3al;yttrium;sulfur
材料科学技术（英文）
The corrosion of an Fe-based alloy containing 15 wt pet Y in H-2-H2S mixtures under 10(-3) Pa S-2 was studied at 600 similar to 800 degrees C in an attempt to find materials with improved sulphidation resistance with respect to pure Fe. The presence of Y has been shown to be beneficial, but not sufficient to the level expected. In fact, the alloy is able to form at all tested temperatures an external FeS layer, beneath which a zone containing a mixture of the two sulphides is also present. Thus, Fe can still diffuse through this region to form the outer FeS layer with non-negligible rate. The corrosion rate of Fe is considerably reduced by the Y addition, but the alloy corrodes still much more rapidly than Y. The sulphidation kinetics is generally rather irregular for both the pure metals, while the corrosion rate of the alloy decreases with time and tends to become parabolic after an initial period of 12 similar to 17 h. The sulphidation behaviour of the alloys is discussed by taking into account the presence of an intermetallic compound Fe17Y2 and the limited solubility of Y in Fe.
关键词:
high-temperature sulfidation;most-reactive component;ni-nb alloys;h2-h2s mixtures;behavior;600-degrees-c-800-degrees-c;oxidation
