Xudong ZHANG
,
Wuzhu CHEN
,
Gang BAO
,
Lin ZHAO
材料科学技术（英文）
This paper describes a way to improve the weld quality through suppressing the porosity formation and restraining the growth of columnar grains by using a weaving beam in laser welding. The experimental results show that the N2 porosity of beam-weaving laser welding low carbon steel can be remarkably reduced with increasing weaving frequency, and porosity can be eliminated when the weaving amplitude is only 0.5 mm; and the Ar porosity in the weld metal is decreased with increasing weaving frequency and amplitude when the welding speed is higher than 0.5 m/min. The beam-weaving laser welding of ultra-fine grained steel has been investigated. The experimental results show that beam-weaving laser welding with appropriate amplitude and frequency can partly restrain the growth of the columnar grain and improve the tensile strength of the weld metal.
关键词:
Welding
,
null
,
null
,
null
Xudong ZHANG
,
Wuzhu CHEN
,
Cheng WANG
,
Lin ZHAO
,
Yun PENG
,
Zhiling TIAN
材料科学技术（英文）
3 mm thick 400 MPa grade ultrafine grained ferritic steel plates were bead-on-plate welded by CO¬2 laser with heat input of 120~480 J/mm. The microstructures of the weld metal mainly consist of bainite, which form is lower bainite plates or polygonal ferrite containing quantities of dispersed cementite particles, mixed with a few of low carbon martensite laths or ferrite, depending on the heat input. The hardness and the tensile strength of the weld metal are higher than those of the base metal, and monotonously increase as the heat input decreases. No softened zone exists in heat affected zone (HAZ). Compared with the base metal, although the grains of laser weld are much larger, the toughness of the weld metal is higher within a large range of heat input. Furthermore, as the heat input increases, the toughness of the weld metal rises to a maximum value, at which point the percentage of lower bainite is the highest, and then drops.
关键词:
Laser welding
,
null
,
null
,
null
Xudong ZHANG
,
Wuzhu CHEN
,
Eiji ASHIDA
,
Fukuhisa MATSUDA
材料科学技术（英文）
In this paper, the microstructures and mechanical properties of underwater laser welds of Type 304 stainless steel were investigated. JISY308L type filler wire was used as filler wire during welding. A gas-shielding nozzle was used to form a local dry cavity surrounding the welding zone. The main results are summarized as follows: (1) The shielding condition of the local dry cavity severely affects the oxygen content of the weld, the worst shielding condition leading to the oxygen content of 800×10-6, which largely increases the oxide inclusions and somewhat reduces the ferrite content. (2) The increase of oxygen content reduces the elongation rate and reduction of area in tensile test, but has no influence on the tensile strength. (3) In appropriate shielding condition, the mechanical properties of the underwater laser welds can be as same as that in the air.
关键词:
Underwater laser beam welding
,
null
,
null
,
null
Journal of Materials Research
The morphology of the dark and bright regions observed by transmission electron microscopy for the Zr(64.13)Cu(15.75)Ni(10.12)Al(10) bulk metallic glass strongly depends on the ion beam parameters used for ion milling. This indicates that the ion beam could introduce surface fluctuation to metallic glasses during ion milling.
关键词:
room-temperature
Philosophical Magazine
The error of Equation (15b) in my article [Z.D. Zhang, Phil. Mag. 87 (2007) p.5309] in the application of the Jordan-Wigner transformation does not affect the validity of the putative exact solution, since the solution is not derived directly from that equation. Other objections of Perk's comment [J.H.H. Perk, Phil. Mag. 89 (2009) p.761] are the same as those in Wu et al.'s comments [F.Y. Wu et al., Phil. Mag. 88 (2008) p.3093; p.3103], which do not stand on solid ground and which I have sought to refute in my previous response [Z.D. Zhang, Phil. Mag. 88 (2008) p.3097]. The conjectured solution can be utilized to understand critical phenomena in various systems, whereas the conjectures are open to rigorous proof.
关键词:
3D Ising model;exact solution;conjecture;critical phenomena;ferromagnetism;magnetic phase transition;model;analyticity
中国腐蚀与防护学报
N。1Atmospheric Corrosivlty for Steels………………………………………………… .LIANG Caideng HO[I i。-tat（6）Caustic Stress Corrosion Cr。king of Alloy 800 Part 2.The Effect of Thiosul执e……………………………………… KONG De-sheng YANG Wu ZHAO Guo-zheng HUANG De.ltL。ZHANG Yu。。he CHEN She。g-bac（13）SERS slid E16CttOCh6iniC81 Stlldy Of Illhibit1Oli M6ch＆tllsth Of ThlollY68 Oil ITOll ID H....
关键词:
