Wei JIN
,
Mingzhou GAO
,
Rui YANG
,
Zhuangqi HU
材料科学技术（英）
The recovery strain, stress and transformation temperature of different pre-strained specimens of Ti44Ni47Nb9 were investigated by tensile test and electrical resistance measurement. The results indicated that pre-strain increases the reverse martensitic transformation temperature (A ' (s)) and hysteresis (A(s) - M-s). The recovery strain and stress are higher if the specimens are pre-strained between M-s and A(s) temperature than outside this temperature range. There exists an optimal pre-strain value, about 10%, at which the specimen exhibits maximum recovery strain and stress.
关键词:
Wei JIN
,
Mingzhou CAO
,
Rui YANG
,
Zhuangqi HU
,
Shaoyu QIU
,
Hong ZOU
材料科学技术（英）
The effect of heat treatment on martensitic transformation behavior has been investigated in Ti44Ni47Nb9 alloy. The relation between transformation temperatures and critical stress of stress induced martensitic transformation is interpreted in terms of thermodynamic theory. It is shown that the decrease in transformation temperature in specimens of slow cooling rate or low temperature aging after solution heat treatment results from the changes of Ni/Ti ratio in the matrix. The increase of critical stress of stress induced martensitic transformation is a consequence of the decrease of transformation temperatures.
关键词:
Ti44Ni47Nb9 shape memory alloy
,
null
,
null
Wei JIN
,
Ying YAN
,
Jian WANG
,
Mingzhou CAO
,
Rui YANG
材料科学技术（英）
The mechanical behavior and the effect of pre-strain on recovery behavior of Ti50Ni47Fe3 (at. pct) alloy were investigated systematically by tensile and recovered tests accompanied by electrical resistance measurement. Ti50Ni47Fe3 alloy has different deformation behaviors at different temperature ranges, the deformation curves in different temperature range can be classified into four kinds. The start temperature of recovery increases with the increase of pre-strain. There exists an optimal deformation condition, at which the specimen exhibits maximum free recovery strain. With increasing pre-strain the recovery stress increases and reaches the maximum at 8% pre-strain. R-phase to parent transition offered about 0.2% recovery strain. With pre-strain increasing the recovery stress increases and reaches to the maximum at 8% pre-strain. The recovery stress is corresponding with the critical stress of stress-induced martensitic transformation.
关键词:
Deformation
,
null
,
null
,
null
,
null
Journal of Applied Physics
Based on the developed multiple-scattering theory [C.-W. Nan and F. S. Jin, Phys. Rev. B 48, 8578 (1993)], an effective-medium theory (EMT) is proposed to treat coupled electromechanical behavior in composite media. The explicit relations for determining effective behavior of piezoelectric composites are derived. To illustrate the technique, numerical results of piezoelectric ceramic/epoxy composites for various particle shapes are presented over the whole range of concentrations. The EMT estimates are shown to be in good agreement with available experimental results. Porous piezoelectric ceramics are also discussed. The EMT predicts a similar critical behavior for heterogeneous piezoelectric materials to recent experiments.
关键词:
electromechanical properties;ceramics
X.B. Tian
,
X.F. Wang
,
A.G. Liu
,
L.P. Wang
,
S. Y. Wang
,
B. Y. Tang and P. K. Chu 1)Advanced Welding Production & Technology National Key Laboratory
,
Harbin Institute of Technology
,
Harbin 150001
,
China 2)Department of Physics & Materials Science
,
City University of Hong Kong
,
China
金属学报(英文版)
The research on plasma immersion ion implantation has been conducted for a little over ten years. Much is needed to investigate including processing technlogy, plasma sheath dynamics, interaction of plasma and surface, etc. Of the processing methods elavated temperature technique is usually used in PIII to produce a thick modified layer by means of the thermal diffusion. Meanwhile plasma ion heating is more recently developed by Ronghua Wei et al[1]. Therefore the temeperature is a critical parameter in plasma ion processing. In this paper we present the theoretical model and analysize the effect of imlantation voltage, plasma density, ion mass,etc on the temperature rise.
关键词:
plasma immersion ion implantation
,
null
,
null
夏小建
量子电子学报
doi:10.3969/j.issn.1007-5461.2009.06.010
采用Wei-Norman方法,求出含时变电压源的介观LC电路随时间演化的精确解,应用相空间准概率分布函数,研究了时变电源作用下介观LC电路相干态的量子特性,结果表明此函数是一个二维运动的Gauss波包,其中心电量和磁通呈余弦和正弦变化.
关键词:
量子光学
,
LC回路
,
介观电路
,
相干态
,
量子态演化
,
相空间的准概率分布函数
WEI Jihe Xi'an Institute of Metallurgy and Construction Engineering
,
China.
材料科学技术（英）
The oxidation of alloying elements during the ESR of stainless steel has been studied. The model previously developed by WEI and Mitchell for the chemical reactions and mass transfer processes during ESR was applied to the remelting of the high Cr steel 1Cr18Ni9(Ti).The laboratory data for the unsteady state A.C.ESR were analyzed and dealt with by the model.When the remelting process reached a steady state,an oxidant(Fe_2O_3 powder)or a deoxidant(Ca-Si powder or metallic Ca)was added to the slag bath.The results showed that this model is applicable to the remelting of stainless steel rather precisely, and it is expected that the model may offer a reliable basis for the control of composition during practical ESR of high alloy steel. Also,the oxidation of Cr in the steel must be noticed when its content is high;but it is entirely possible to adjust the Cr content of ingot within a considerable range,using a special technique by means of the slag-metal reactions during the remelting.
关键词:
ESR
,
null
,
null
,
null
,
null
Acta Materialia
In a first report [Jin ZH.. Gumbsch P, Ma E, Albe K, Lu K, Hahn H, et al. Scripta Mater 2006;54:1163], interactions between screw dislocation and coherent twin boundary (CTB) were studied via molecular dynamics simulations for three face-centered cubic (fcc) metals, Cu, Ni and Al. To complement those preliminary results, purely stress-driven interactions between 60 degrees non-screw lattice dislocation and CTB are considered in this paper. Depending on the material and the applied strain, slip has been observed to interact with the boundary in different ways. If a 60 degrees dislocation is forced by an external stress into a CTB, it dissociates into different partial dislocations gliding into the twin as well as along the twin boundary. A sessile dislocation lock may be generated at the CTB if the transited slip is incomplete. The details of the interaction are controlled by the material-dependent energy barriers for the formation of Shockley partial dislocations from the site where the lattice dislocation impinges upon the boundary. (c) 2007 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
关键词:
dislocation;slip;twinning;twin grain boundary;molecular dynamics;molecular-dynamics simulation;grain-boundaries;nanocrystalline;materials;cross-slip;rate sensitivity;deformation;copper;strength;aluminum;fcc
