Journal of Materials Research
Based on the best bulk metallic glass (BMG) forming alloy in the Mg-Cu-Y ternary system, we introduced Ag (or Ni) to partially substitute for Cu to improve the glass-forming ability (GFA). The objective of this paper is twofold. First, we illustrate in detail a recently developed search strategy, which was proposed but only briefly outlined in our previous publication [H. Ma, L.L. Shi, J. Xu, Y. Li, and E. Ma: Discovering inch-diameter metallic glasses in three-dimensional composition space. Appl. Phys. Lett. 87, 181915 (2005)]. The protocol to navigate in three-dimensional composition space to land large BMGs is spelled out step-by-step using the pseudo-ternary Mg-(Cu,Ag)-Y as the model system. Second, our ability to locate the best BMG former in the composition tetrahedron allows us to systematically examine, and conclude on, the effects of a given alloying element. The large improvement in glass-forming ability in the Mg-(Cu,Ag)-Y system relative to the based ternary will be contrasted with the reduced glass-forming ability in the Mg-(Cu,Ni)-Y pseudo ternary system. It is demonstrated that the improvement of glass-forming ability requires judicious choice of substitutional alloying elements and concentrations, rather than simple additions of multiple elements assuming the "confusion principle."
关键词:
bulk metallic-glass;shaped copper mold;amorphous-alloys;thermal-stability;ternary-system;casting method;p system;diameter;zr;mm
孙保基
,
张葆
,
宋策
,
龙思源
液晶与显示
doi:10.3788/YJYXS20163109.0921
针对TLD算法的特征点无法有效表述目标问题，提出了一种基于角点增强改进的TLD目标跟踪算法。改进算法在跟踪模块加入了对目标表述能力更强，具有光照不敏感性和旋转不变性的 Shi-Tomas 角点作为跟踪特征点。跟踪器运行时，在角点经光流法跟踪和双向误差检测后，利用剩余的稳定角点定位目标窗口。对照结果表明，改进算法在面对目标抖动和形变时可以稳定跟踪；有效抑制因跟踪平滑点造成的漂移现象；提高了跟踪的稳定性。针对 TLD算法跟踪过程中因在线模板积累造成的计算量持续增大、实时性持续降低的问题，提出了一种依据相似度中值的模板判断删除机制。该删除机制在模板积累到设定阈值时运行，根据模板与当前目标的相似度，删除不再具备代表性的模板；调整模板空间并更新模板数目。实验表明，该删除机制在应对模板更新快、持续时间长的跟踪情景时有效降低算法计算量，实时性可提高约20％。
关键词:
目标跟踪
,
TLD
,
角点特征
,
在线模板
李凤娟
,
吕国光
金属世界
doi:10.3969/j.issn.1000-6826.2014.04.14
通过对烧结配料所需原料及对冷烧结矿成品检验采制样方法的分析，找出影响检验结果真实性的因素，采取有效的改进措施，使本钢原料厂一次配料、本钢炼铁厂265 m2烧结二次配料及265 m2烧结系统各项稳定率有了很大的提高，烧结矿实物质量和各项技术质量指标有了很大的进步，保证了高炉的稳定顺行。
提高本钢265 m2冷烧结矿及原料检验代表性的实践
Practice of Improving the 265 m2 Cold Sinter and Raw Material Inspection Representative
供稿|
李凤娟,吕国光/
LI Feng-juan, LV Guo-guang
DOI：10.3969/j.issn.1000-6826.2014.04.14
导读内容
本钢炼铁厂265 m2烧结机生产所需要的含铁原料比较复杂，一次配料料种较多，且烧结含铁原料是由本钢原料厂二车间供料，原料质量的不稳定，会影响烧结矿质量的提高和新一号高炉的强化及高炉技术指标的改善。本钢质量管理中心驻冷烧检查站加强了对烧结配料所需原料及对冷烧结矿成品检验采制样代表性的研究，采取了一些改进措施，达到了良好的效果。含铁料成分稳定率、烧结矿各项质量和技术指标在稳步地提高。下面，对本钢质量管理中心驻冷烧检查站就提高采样及检验过程的准确性所采取的措施和办法进行说明。
烧结矿采样是半自动采样，每两小时采样一次，作为一个批次，来代表整个2h烧结矿的成份。
关键词:
