REN Jianshi ZHAO Huilin ZHANG Gongshu Institute of Metal Research
,
Academia Sinica.Shenyang
,
China ZHANG Gongshu
,
Senior Engineer
,
Institute of Metal Research
,
Academia Sinica
,
Shenyang 110015
,
China
金属学报(英文版)
Glow discharge cathodic sputtering of alloys containing second phase precipitates or injected oxide particles has been observed with energy dispersive X-ray spectrometer and scanning electron microprobe.It was shown that the formation of cones during the sputtering in these alloys is due to masking of the matrix by glow sputtering second phase precipitates or oxide particles.At steady state,the density of cottes were found to be a function of the densities pre- cipitates or oxide particles in bulk alloy.In addition to the changes of local sputtering rate,the electrostatic effect may play a role on the formation fo cones.
关键词:
glow discharge
,
null
,
null
MA Zongyi YAO Zhongkai Harbin Institute of Technology
,
Harbin
,
China
金属学报(英文版)
The SiC_w/Al composite prepared by squeeze casting has a combination of superior room temperature specific strength and modulus together with excellent thermal properties.The extrusion can make an improvement on the strength and ductility of the composite from 582 MPa as squeeze casted up to 639 MPa,and on the transformation from isotropic to the anisotropic structure.This seems to be explained by the orientation of whiskers and the densification of dislocations in matrix.TEM observation indicates that the stacking fault is the usual planar defect on the SiC_w surface. composite;;SiC whisker;;Al alloy;;microstructure
关键词:
composite
,
null
,
null
,
null
Corrosion
This paper introduces the design of a localized corrosion rate monitoring instrument that can monitor and evaluate the maximum and stable localized corrosion rate of a nonpassivable metal in a corrosive environment by measuring the current density in a corrosion sensor with an occluded anode.
关键词:
instrument;localized corrosion rate;monitor
张麦仓
,
董建新
,
曾燕屏
,
谢锡善
,
罗子健
金属学报
利用热力耦合有限元程序FORMT,对PM René 95合金中等尺寸(外径尺寸约为630 mm)涡轮盘的等温锻造工艺进行了模拟式设计.结果表明,采用TZM钼基合金模具,在1050℃以接近10-3s.的应变速率进行闭式模锻和开式模锻,模具材料均能满足使用要求,且开式模锻设备最大载荷不超过31×103kN;采用K21合金模具,在1000℃以相同条件等温成形,模具材料因变形热效应及边界摩擦引起温升而失效且所需设备吨位相对较大.
关键词:
PM
,
null
,
null
,
null
张麦仓
,
董建新
,
曾燕屏
,
谢锡善
,
罗子健
金属学报
doi:10.3321/j.issn:0412-1961.2002.10.022
利用热力耦合有限元程序FORMT,对PM René 95合金中等尺寸(外径尺寸约为630 mm)涡轮盘的等温锻造工艺进行了模拟式设计.结果表明,采用TZM钼基合金模具,在1050℃以接近10-3s.的应变速率进行闭式模锻和开式模锻,模具材料均能满足使用要求,且开式模锻设备最大载荷不超过31×103kN;采用K21合金模具,在1000℃以相同条件等温成形,模具材料因变形热效应及边界摩擦引起温升而失效且所需设备吨位相对较大.
关键词:
PM René 95合金,等温锻造,热力耦合有限元,模拟式工艺设计
Juhua HUANG
,
Jinjun RAO
,
Xuefeng LI
材料科学技术（英文）
Sheet metal forming is widely applied to automobile, aviation, space flight, ship, instrument, and appliance industries. In this paper, based on analyzing the shortcoming of general finite element analysis (FEA), the conception of parametric finite element analysis (PFEA) is presented. The parametric finite element analysis, artificial neural networks (ANN) and genetic algorithm (GA) are combined to research thoroughly on the problems of process parameters optimization of sheet metal forming. The author programs the optimization scheme and applies it in a research of optimization problem of inside square hole flanging technological parameters. The optimization result coincides well with the result of experiment. The research shows that the optimization scheme offers a good new way in die design and sheet metal forming field.
关键词:
Sheet metal forming
,
null
,
null
,
null
