齐召庆
,
汪宏涛
,
薛明
功能材料
doi:10.3969/j.issn.1001-9731.2016.02.010
采用改进的非接触式混凝土收缩测定仪及标靶,研究了m(M)/m(P)比值(MgO与KH2PO4的质量比)对磷酸镁水泥石自收缩行为的影响,运用八通道微量量热仪、压汞仪、X射线衍射仪、扫描电子显微镜及能谱仪等分析手段,分析了m(M)/m(P)比值对磷酸镁水泥石自收缩的作用机理.结果表明,磷酸镁水泥石的自收缩呈现出3个阶段的特征,即早期的迅速收缩阶段、微膨胀阶段、收缩缓慢发展阶段.随着m(M)/m(P)比值的增大,由于磷酸镁水泥石的水化放热量降低,水泥石内部孔隙率增大,水化产物结晶度降低,水泥石结构疏松,所以,自收缩率减小.
关键词:
磷酸镁水泥
,
自收缩
,
m(M)/m(P)比值
F.J. Liu
,
M.C. Zhang
,
J.X. Dong
,
Y.W. Zhang
金属学报(英文版)
High temperature oxidation behaviors of FGH96 P / M superalloy have been studied in air at temperatures ranging from 600 to 1000℃. By means of isothermal oxidation testing, X-ray
diffraction, SEM (scanning electron microscopy) and EDS (energy dispersive X-ray spectroscopy) analyses, the oxidation kinetics as well as the composition and morphology of scales were investigated. Thermodynamic calculations were used to explain the oxidation mechanism. The results showed that as the oxidation temperature increased, the oxidation rate, the scale thickness and scale spallation increased. FGH96 P / M superalloy exhibits good oxidation resistance at temperature below 800℃. The oxidation kinetics follows an approximately parabolic rate law, and the
oxide layer was mainly composed of Cr2O3, TiO2, and a little amount of NiCr2O4. The oxidation is controlled by the transmission
of chromium, titanium, and oxygen through the oxide scale.
关键词:
FGH96 P/M superalloy
,
null
,
null
Yong LIU
,
Baiyun HUANG
,
Kechao ZHOU
,
Hongwu OUYANG
,
Yuehui HE
材料科学技术（英文）
In order to overcome the shortcomings of conventional hot pressing, a novel near net-shape technique, called radial hot pressing, for P/M parts with large height-to-diameter (H/D) ratio was introduced. Effects of processing parameters on the microstructures and density of P/M TiAl base alloy valves were studied. Results show that the radial hot pressing is an effective technique for manufacturing valves with a H/D ratio of about 10:1, and the perfect joint interface between the Mo sheet and the parts is helpful for subsequent HIPing.
关键词:
Near net-shape technique
,
null
,
null
YANG Xia
,
GUO Shiju
钢铁研究学报(英文版)
Liquidphase enhanced sintering of powder metallurgy (P/M) 316L stainless steel by addition of sintering aids was studied. 2%-8% of prealloyed FeMoB powder with two different particle sizes was added as sintering aids, and the specimens were sintered in vacuum at 1 200-1 350 ℃. The results show that the fine FeMoB powder (5-10 μm) has stronger activated effect. The sintered density increases with the increase in sintering aid content or sintering temperature. Warm compaction has a better effect on the control of dimensional precision of compacts. The prealloyed FeMoB powder deviated from Mo2FeB2 component can also be sintering aid of P/M 316L stainless steel.
关键词:
P/M 316L stainless steel;liquidphase sintering;activated sintering;FeMoB;sintering aid
曹笃盟
,
李志友
,
周科朝
稀有金属材料与工程
采用固相反应法制备了Li1+xV3-yMyO8(M=Mo,P;0≤y≤0.4),研究了不同Mo和P含量对Li1+xV3O8相的影响,并首次对其进行了高温阴极放电性能的研究.结果表明:Mo和P掺杂量分别为y≤0.2和y＜0.2时可获得纯Li1+xV3O8相;Mo掺杂使Li1+xV3O8峰值电压提高0.3 V,比容量提高25%,嵌入的Li+量最高可达x=3.8;P掺杂(y≤0.20)对Li1+xV3O8的峰值电压和比容量影响较小.化学嵌锂实验也证实掺杂后的材料具有更快的Li+嵌入速度.
关键词:
Li1+xV3O8
,
热电池
,
掺杂
,
比容量
Zhenya Zhang
材料科学技术（英文）
This study investigated the microstructures and mechanical properties of ZK60 alloy prepared by a simplified rapid solidification powder metallurgy (RS P/M) processing system (S-RS P/M), which consists of warm press in dry air and hot extrusion. Microstructure characterizations showed that S-RS P/M alloy consisted of magnesium matrix and oxide stringers of ~1 μm in width. TEM (transmission electron microscopy) observations illustrated nano-size magnesia particles (10{30 nm) constituted oxide stringer in detail. Due to a relatively higher volume of nano-size magnesia particle produced during S-RS P/M process, 0.2% yield strength of S-RS P/M ZK60 alloy was found to be as high as 382 MPa, which is 10% higher than that of RS P/M alloy. The improvement in mechanical properties is mainly attributed to the combination effects of Orowan mechanism and coe±cient of thermal expansion (CTE) mismatch because of the approximately same average grain size.
关键词:
Microstructure
Journal of Materials Research
MAX-phase carbides (M is an early transition metal, A is an A-group element) exhibit an interesting bonding characteristic of alternative stacking of strong M-C bonds and relatively weak M-A bonds in one direction. In the present first-principles total energy calculations, we establish the relationship between mechanical properties and electronic structure for ternary M(2)AC (M = Ti, V, Cr. A = Al, Si, P, S) carbides. By systematically tuning elements on the M and A sites, pronounced enhancements of bulk modulus, elastic stiffness, and ideal shear strength are achieved in V-containing V(2)AC (A = Al, Si, P, and S) carbides. It is suggested that tailoring on the A site is more efficient than on the M site in strengthening the mechanical properties of studied serial carbides. The results highlight a general trend for tailor-made mechanical properties of ternary M(2)AC carbides by control of chemical bonding.
关键词:
strength;solids;shear;dislocations;ti3sic2
