WANG Dening
,
WANG Weiyuan Ion Implantation Lab.
,
Shanghai Institute of Metallurgy
,
Academia Sinica
,
Shanghai
,
China Associate Professor
,
Laboratory No.6
,
Shanghai Institute of Metallurgy
,
Academia Sinica
,
Shanghai 200050
,
China
金属学报(英文版)
The formulae for calculating the electronic stopping power.for heavy ion implanting into metal are derived by using Wigner-Sietz radius r_s,equivalent charge,Fermi velocity and Ziegler's values of hydrogen electronic stopping power.Meanwhile the.formulae of electronic stopping power S_e(E)for alloys with boride or CsCl structure are also proposed.The calculated results are found as follows:these formulae are suitable only for mono-or bi-borides,but not for borides with more complex structure such as Cr_5B_3 or W_2B_5;the coefficient γ,of S_e(E)for al- loys with CsCI structure deviating from Bragg's S_e(E)is directly proportional to charge trans- fer in alloy.This means the larger the charge transfer is,the more stronger the metallic bond is.Hence the S_e(E)created by metallic bond in alloys will increase; there is a tendency for it to increase with increasing separation of two components in alloy on either side of Cr group at same periods,when the two components are in different periods,the tendency is more larger.
关键词:
metal
,
null
,
null
,
null
Corrosion Science
The early stages of the evolution of atmospheric corrosion of carbon steels exposed in both a laboratory simulated and a natural atmosphere environment in Shenyang have been observed by in situ scanning electron microscopy. In the case of laboratory cyclic wet-dry tests, even though the chloride content level is very low, filiform corrosion is initiated in the early stage. The filiform corrosion grows in random directions, forming a network of ridges. White nodules nucleate and grow on the ridges during continued corrosion and eventually connect with each other to form the initial corrosion scale. Pits were also found on the surface beneath corrosion products. In the case of a natural atmospheric environment, both filiform corrosion and other localized corrosion, such as pitting and inter-granular attack take place in the initial stage. It is obvious that there is variety of localized corrosion in the initial stage of atmospheric corrosion. (C) 2007 Elsevier Ltd. All rights reserved.
关键词:
steel;atmospheric corrosion;initial stage;localized corrosion;in-situ;iron;electrolyte;thickness
Author S.T. TU
,
J.M. Gong and X. Ling Nanjing University of Chemical Technology
,
Nanjing 210009
,
ChinaManuscript received 18 October 1998
金属学报(英文版)
In order to interpret the test results of crossweld specimens for application in practical welded components, the present paper studies the high temperature behavior of laboratory cross weld specimens in terms of the uniaxial material tests and numerical simulations. It is found that the crossweld specimen may be used for the high temperature strength assessment, but can hardly be used for life assessment of the practical welded components, which depends on the loading conditions of the components.
关键词:
high temperature
,
null
,
null
,
null
,
null
Materials Chemistry and Physics
The corrosion behaviour of CortenA weathering steel has been investigated using a laboratory accelerated test that involved cyclic wet/dry conditions in Qinghai salt lake water diluted 30 times The characteristics of the rust layers on tested samples were observed by SEM and EPMA analyzed by IRS and XRD and studied by polarization and EIS measurements The weight loss was almost linear indicating that the rust layer had no retarding effect on the corrosion process The crystalline components of the rust layers consisted primarily of beta-FeOOH magnetite (Fe(3)O(4)) and gamma-FeOOH As the corrosion proceeded the amount of beta-FeOOH decreased while that of magnetite and gamma-FeOOH increased XRD EDAX and EPMA indicated that the complex corrosion products magnesioferrite (MgFe(2)O(4)) and iowaite (Mg(4)Fe(OH)(8)OCl 4H(2)O) probably existed in the rust layer in which case they will have had an important Influence on the protectiveness of the rust layer The results of electrochemical measurements showed that the rust layer exhibited high reduction reactivity which facilitated the corrosion of weathering steel in the wetting process The large rust capacitance and small rust resistance indicated that the rust layer had a loose and porous structure which provided poor protection (c) 2010 Elsevier B V All rights reserved
关键词:
Elements;Corrosion test;Electrochemical techniques;Electron probe;low-alloy steels;atmospheric corrosion;carbon-steel;electrochemical;impedance;room-temperature;rust layers;iron;mechanism;products;environment
Surface & Coatings Technology
Using a halide-activated pack-cementation method but at a temperature (600 degrees C) noticeably lower than normal, an eta-Fe(2)Al(5) coating and two delta-Ni(2)Al(3) coatings with and without dispersions of CeO(2) nanoparticles were developed respectively on a low-carbon steel and the steel pretreated with an electrodeposited film of Ni or Ni-CeO(2). The erosion-corrosion (E-C) performance of the three aluminide coatings during 100 h exposure at similar to 600 degrees C in a coal-firing laboratory-scale fluidized-bed combustor (FBC) was investigated, by mounting the aluminized samples onto a rig which maintained rotation for accelerating the relative impacting speed of flying solid particles (mainly SiO(2) bed materials). The eta-Fe(2)Al(5) and the CeO(2)-free delta-Ni(2)Al(3) coatings experienced an unacceptable recession rate. Compared to the two CeO(2)-free aluminide coatings, the CeO(2)-dispersed delta-Ni(2)Al(3) coating offered profoundly improved E-C resistance, because the latter coating was not only strengthened by the CeO(2) dispersion and grain refinement, it also could grow a more adherent alumina scale. (C) 2011 Elsevier B.V. All rights reserved.
关键词:
Erosion-corrosion;CeO(2)-dispersion-strengthening;Aluminizing coating;Grain refinement;Hardening;Reactive element effect;oxidation resistance;reactive elements;alloy-steels;water-vapor;power-plant;nickel;combustion;mechanisms;additions;behavior
Xingzhong ZHAO
,
Jiajun LIU and Baoliang ZHU (Tsinghua University
,
Beiing 100084
,
China)Cuiyuen WANG (Zhengzhou Research Institute of Mechanical Engineering
,
Zhengzhou 450002
,
China)
材料科学技术（英文）
The antiwear properties of two wheel/rail lubricating oils were tested and compared on an Amsler machine. Under same testing conditions, oil A (developed by authors) showed much better wear resistance and higher load-carrying capacity than oil B (imported from abroad). The X-ray diffraction (XRD) analyses of the worn surfaces showed that different extreme pressure (EP) lubricating films were formed on the surfaces when the rollers were lubricated with different oils under boundary Iubrication condition. The EP film of oil A was a composite film containing three compounds, FeO, FeSx and FeP, while oil B formed only a simple EP film of FePO4. The composite EP film showed lower shear strength and better antiwear property than the simple EP film,which brought about different wear resistance of the two wheel/rail lubricating oils.
关键词:
