LIU Changhui
,
HE Huahui
,
SHEN Xiang
,
LI Haihua
钢铁研究学报(英文版)
Electroless CoFeB films with good soft magnetic properties were fabricated on polyester plastic substrate from sodium tartarate as a complexing agent. The plating rate of electroless CoFeB films is a function of concentration of sodium tetrahydroborate, pH of the plating bath, plating temperature and the metallic ratio. The estimated regression coefficient b0-b3 confidence interval, residual error r and confidence interval rint were confirmed by a computer program. The optimal composition of the plating bath was obtained and the dynamic electromagnetic parameters of films were measured in the 2-10 GHz range. At 2 GHz, the μ′, μ″ of the electroless CoFeB films were 304 and 766, respectively, as the concentration of reducer is 1 g/L. Magnetic hysteresis loop of the deposited CoFeB films show a remanence close to the saturation magnetization and coercivity of about 557-1274 A/m. The loops along the hard axis display low anisotropic field Hk of 2 388-3 582 A/m.
关键词:
electroless CoFeB deposits;deposition rate;multiple linear regression;coercivity;magnetic hysteresis loop
周萧明
,
胡更开
复合材料学报
doi:10.3321/j.issn:1000-3851.2004.06.026
提出了预测复合材料非线性电位移和电场强度关系的一种解析方法,该方法基于各向材料的割线介电常数,将非线性问题转化成一系列线性问题来求解.该方法适用于任意各向异性复合材料和组分材料的非线性性质,而常用的Stroud和Hui的模型只适用于各向同性复合材料和组分材料的弱线性.证明了本文方法具有Ponte Castaneda提出的变分结构.计算结果表明,当基体非线性较小时,本文模型的预测与Stroud和Hui的模型一致,但当基体非线性系数增大时,本文模型能给出合理的预测结果,而Stroud和Hui的模型则会超出基体和夹杂的性能范围.
关键词:
复合材料
,
介电常数
,
非线性
,
割线方法
徐卫兵
,
戈明亮
,
何平笙
应用化学
doi:10.3969/j.issn.1000-0518.2001.09.011
用熔融插层法制备聚甲醛/蒙脱土纳米复合材料,用X射线衍射研究聚甲醛及复合材料的微观结构,表明复合材料是纳米复合材料.用DSC法研究其非等温结晶行为,对所得数据分别用Jeziorny法、Ozawa法和Liu法进行处理.结果表明,Jeziorny法和Liu法处理非等温结晶过程比较理想.聚甲醛及聚甲醛/有机蒙脱土纳米复合材料的结晶活化能分别为334.6和196.9 kJ/mol,说明有机蒙脱土的加入,降低了聚甲醛的结晶活化能,且t1/z缩短,起到了异相成核的作用.
关键词:
聚甲醛
,
蒙脱土
,
纳米复合材料
,
非等温结晶动力学
王平华
,
徐国永
应用化学
doi:10.3969/j.issn.1000-0518.2004.08.007
用熔融复合法制备聚丙烯/凹凸棒土纳米复合材料,用DSC法研究其非等温结晶行为,对所得的数据分别用Jeziorny法、Ozawa法和Liu法进行处理.结果表明,Jeziorny法和Liu法处理非等温结晶过程比较理想.聚丙烯及聚丙烯/凹凸棒土纳米复合材料的结晶活化能分别为194.1和162.8 kJ/mol,表明凹凸棒土的加入,降低了聚丙烯的结晶活化能,且t1/2缩短,起到了异相成核作用.
关键词:
聚丙烯
,
凹凸棒土
,
纳米复合材料
,
非等温结晶动力学
张莉
,
马敬红
,
梁伯润
,
余亦华
高分子材料科学与工程
在氮气氛中采用热重分析的方法对热致液晶共聚酯60PHB/PEN的热降解动力学进行了研究.采用Friedman和Chang两种单一加热速率方法对活化能Ea、反应级数n和频率因子Z等降解反应动力学参数进行了分析.讨论了加热速率和计算方法对热稳定性及降解动力学参数的影响.
关键词:
热致液晶共聚酯
,
热降解
,
动力学
,
热稳定性
金属学报
Volu扣ne 27SeriesB1991AUTHOR INDEX CCAO Guanghan(曹光旱)············……6一B科6CAo weijie(曹卫恋)..················……5一B32oCAO Yilin(曹益林)··················……6一B443CHANG Xin(常听)···············……1一B48CHE Guang邻n(车广灿)·············一6一B科0CHEN Erbao(陈二保)···············……6一B410CHEN Jia....
关键词:
徐颖
,
温卫东
,
崔海坡
材料科学与工程学报
doi:10.3969/j.issn.1673-2812.2006.01.020
针对复合材料层板在冲击载荷下,各种损伤的产生和扩展是一个随载荷、时间和空间而演变的过程,发展了复合材料层合板低速冲击逐渐累积损伤预测方法.采用刚度退化技术和改进的Chang-Chang失效准则、显式有限元法来模拟复合材料层合板受到低速冲击下逐渐损伤过程.使用所发展的方法分析了[0m/90n/0m]铺层的复合材料层合板在低速冲击过程中的逐渐损伤扩展,结果表明本文的方法能较好地模拟复合材料层板在低速冲击下的损伤扩展及变形过程,计算结果与实验结果吻合较好;对不同冲击能量下层合板损伤扩展研究表明,冲击能量与分层损伤面积成线性关系.
关键词:
复合材料层合板
,
冲击
,
逐渐累积损伤
,
破坏机理
,
数值模拟
张鹏飞
,
金海波
复合材料学报
建立了有效的复合材料层合板结构冲击损伤分析方法,层合板面内损伤采用改进的Chang/Chang失效准则做判据,得到面内各类损伤形式.层间损伤采用与Mixed-Mode粘接元等效的TIEBREAK接触模拟.利用此分析方法,从复合材料薄壁结构设计需要出发,研究了在低能量冲击下,铺层的层间角度、铺层方向、铺层重叠对层合板结构冲击损伤阻抗的影响规律,并对它们的综合影响进行了总体分析,得到了能提高层合板结构损伤阻抗的铺层顺序设计指导.最后用该设计指导对某种铺层结构进行了重新设计和有限元模拟,验证了该设计指导的可行性和有效性.
关键词:
冲击损伤
,
分层损伤
,
TIEBREAK接触
,
铺层顺序
,
损伤阻抗
Scripta Materialia
A recent comment on a previously published paper addressed the invalid explanation of the off diagonal interdiflusion coefficients of the beta-Ni(Al,Cr) phase in the Ni-Cr-Al system according to the symmetric property of the thermodynamic matrix. In this paper, the experimental data presented by Hou et al. was reanalyzed and the interdiffusion coefficient matrix was estimated again. The results of the analysis have been discussed in terms of a brief reply to the comments of Liu and Liang. (C) 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
关键词:
Diffusion;Intermetallic compound;Ni-Cr-Al
