中国腐蚀与防护学报
N。1Atmospheric Corrosivlty for Steels………………………………………………… .LIANG Caideng HO[I i。-tat（6）Caustic Stress Corrosion Cr。king of Alloy 800 Part 2.The Effect of Thiosul执e……………………………………… KONG De-sheng YANG Wu ZHAO Guo-zheng HUANG De.ltL。ZHANG Yu。。he CHEN She。g-bac（13）SERS slid E16CttOCh6iniC81 Stlldy Of Illhibit1Oli M6ch＆tllsth Of ThlollY68 Oil ITOll ID H....
关键词:
徐菊良
,
邓博
,
孙涛
,
李劲
,
蒋益明
金属学报
doi:10.3724/SP.J.1037.2009.00598
利用Thermo-Calc软件并结合金相显微镜,定性研究了2205双相不锈钢在800℃下敏化不同时间后的微观组织演变过程.通过研究扫描速率、介质成分、介质温度和试样表面状态优化了双环电化学动电位再活化法(DL-EPR),并用该优化方法研究了2205双相不锈钢晶间腐蚀敏感性.结果表明:DL-EPR法能定量评价σ相对2205双相不锈钢晶间腐蚀敏感性的影响,随敏化时间延长,σ相含量增多,晶jian 腐蚀敏感性也随之增加.腐蚀形貌的观测验证了这一规律,
关键词:
2205双相不锈钢
,
DL-EPR
,
晶间腐蚀敏感性
,
σ相
Y.D.Xiao
,
W.X.Li
,
D.Jacovkis
,
M.T.Clavaguera-Mora
,
J.Rodriguez-Viejo
,
N.Clavaguera
金属学报(英文版)
Rapidly solidified Al87Ni7Cu3Nd3 metallic glasses, prepared by using melt spinning, were treated under both isothermal and non-isothermal regime. The amorphous rib-bon and the annealed samples were closely examined by means of differential scan-ning calorimetric, conventional X-ray diffraction and high resolution transmission electron microscopy with selected-area electron diffraction, with special interest in pri-mary crystallization into α-Al nanocrystalline particles, in order to understand struc-tural characteristics of Al-based amorphous/nanocrystalline alloys, and nucleation and grain growth mechanism on the nanometer scale during primary crystallization. The results show that, the as-prepared ribbons are fully amorphous and homogeneous in the micron scale, but contain high density of quenched-in clusters or crystallite embryos. Primary crystallization mainly leads to formation of two-phase mixture of α-Al crystal and residual amorphous phase. The annealed ribbons exposed isother-mally at 110℃ for 5, 130 minutes and heated continuously up to less than 310℃ at 40℃/min consist of large amount of α-Al fec crystal nanoparticles dispersed uni-formly in an amorphous matrix. However, a very little amount of finer orthorhombic Al3Ni intermetalics particles exist in the annealed ribbons heated up to 310℃. During primary crystallization, the leading kinetic mechanics to impede growth of the α-Al crustal is soft impinaement, instead of geometric impinqement.
关键词:
rapid solidification
,
null
,
null
李凤娟
,
吕国光
金属世界
doi:10.3969/j.issn.1000-6826.2014.04.14
通过对烧结配料所需原料及对冷烧结矿成品检验采制样方法的分析，找出影响检验结果真实性的因素，采取有效的改进措施，使本钢原料厂一次配料、本钢炼铁厂265 m2烧结二次配料及265 m2烧结系统各项稳定率有了很大的提高，烧结矿实物质量和各项技术质量指标有了很大的进步，保证了高炉的稳定顺行。
提高本钢265 m2冷烧结矿及原料检验代表性的实践
Practice of Improving the 265 m2 Cold Sinter and Raw Material Inspection Representative
供稿|
李凤娟,吕国光/
LI Feng-juan, LV Guo-guang
DOI：10.3969/j.issn.1000-6826.2014.04.14
导读内容
本钢炼铁厂265 m2烧结机生产所需要的含铁原料比较复杂，一次配料料种较多，且烧结含铁原料是由本钢原料厂二车间供料，原料质量的不稳定，会影响烧结矿质量的提高和新一号高炉的强化及高炉技术指标的改善。本钢质量管理中心驻冷烧检查站加强了对烧结配料所需原料及对冷烧结矿成品检验采制样代表性的研究，采取了一些改进措施，达到了良好的效果。含铁料成分稳定率、烧结矿各项质量和技术指标在稳步地提高。下面，对本钢质量管理中心驻冷烧检查站就提高采样及检验过程的准确性所采取的措施和办法进行说明。
烧结矿采样是半自动采样，每两小时采样一次，作为一个批次，来代表整个2h烧结矿的成份。
关键词:
