李开明
,
李亚洲
,
冯维贵
,
林长
量子电子学报
doi:10.3969/j.issn.1007-5461.2007.05.014
采用非线性反馈控制,用附加了带参数的正弦项对Chen系统进行了有效的控制.随着参数k的逐渐增大,系统的动力学行为呈现出一系列的变化.数值研究结果表明:随控制参数的增大,驱动信号的强度渐大,混沌系统由混沌运动到周期轨道,最终到一相点.
关键词:
混沌
,
Chen系统
,
不动点
,
Lyapunov指数
,
反馈控制
Journal of Materials Research
The morphology of the dark and bright regions observed by transmission electron microscopy for the Zr(64.13)Cu(15.75)Ni(10.12)Al(10) bulk metallic glass strongly depends on the ion beam parameters used for ion milling. This indicates that the ion beam could introduce surface fluctuation to metallic glasses during ion milling.
关键词:
room-temperature
H.P. Chen and Z.J. Deng (State Key Lab. for Mechanical Behavior of Materials
,
Xi'an Jiaotong University
,
Xi'an 710049
,
China)
金属学报(英文版)
The effect of specimen thinkness on JR resistance curve has been investigated using low and middle strength steels. As the J dominance regime is reached, the initial J-integral values, J(i), are definite even if the elastic component Ji(e) and plastic component Ji(p)vary with the thinkness of specimen. The wider the specimen width, the larger the Ji(e)/Ji and the smaller the Ji(p)/Ji. The crack propagation resistance, dJR/da and dJp/da, decreases, while dJe/da increases linearly with increasing specimen thinness.Based on the above experimental results, an empirical formula dJ/da = α+β. B is given, which can be used to evaluate the safety of practical structural components.A modified J-integral is presented, upon which a new view is Put forward that the increase in crack growth resistance is induced mainly by the increase in the plastic J-integral component with the crack propagation,
关键词:
: fracture mechanics
,
null
,
null
,
null
张淑佳
,
卢炎麟
,
任立义
,
洪起超
金属学报
对20 g钢高温断裂韧性随加载速率的变化规律进行了实验研究.在400℃和500℃下,分别测量了几种加载速率下20 g钢的Ji值.实验结果表明:Ji值随应变速率的增大而有较大幅度的降低;在同一应变速率下,400℃时的Ji值小于500℃时的Ji值;400℃时裂纹扩展比500℃时更快.因此,当温度在400℃附近时更应注意避免超载.
关键词:
断裂韧性
,
null
,
null
周兰花
,
陶东平
,
曾富洪
稀有金属
doi:10.3969/j.issn.0258-7076.2011.04.011
在求解分子相互作用体积模型(MIVM)中的分子对位能参数B(ij),B(ji)时,为避免出现计算超量问题,基于遗传算法,提出了一种新算法--多个体参与交叉遗传算法,并给出了新算法的实现方案.在新算法中,采用了轮盘选种法与优秀个体保存、多个体参与交叉和多点变异等策略;选择B(ij),B(ji)个体时,按照适应度函数值愈大,个体被选中的概率愈大的原则,选择二元合金溶液中一组元活度的计算值与实验测定值之间偏差(σ)建立的适应度函数f(x)最大为优化目标.采用Matlab软件编制新算法下的B(ij),B(ji)计算程序,并分别求算了Cd-Bi,Cd-Pb,Cd-Sn,Bi-Pb,Bi-Sn,Pb-Sn等6组二元合金溶液在773 K下合金溶液的参数B(ij),B(ji)优化值.由B(ij),B(ji)计算优化值和其他一些资料数据,使用MIVM进一步预测773 K下Cd-Bi-Pb,Cd-Bi-Sn,Cd-Pb-Sn,Cd-Bi-Pb-Sn多元合金溶液中组元Cd的活度,模型预测值与实验测定值之间的相对误差低于4.6%,偏差低于0.022,两者吻合很好.结果表明,所提出的多个体参与交叉遗传算法为求解MIVM中的参数B(ij),B(ji)提供了一种有力工具,从而也能提高MIVM对多元合金溶液中组元活度的预测效果.
关键词:
MIVM模型
,
分子对位能参数Bij
,
Bji
,
遗传算法
,
活度
金属学报
Volu扣ne 27SeriesB1991AUTHOR INDEX CCAO Guanghan(曹光旱)············……6一B科6CAo weijie(曹卫恋)..················……5一B32oCAO Yilin(曹益林)··················……6一B443CHANG Xin(常听)···············……1一B48CHE Guang邻n(车广灿)·············一6一B科0CHEN Erbao(陈二保)···············……6一B410CHEN Jia....
关键词:
