XIONG Wei
,
JIA Juan
,
CHEN Jia-chao
,
SHANG He-ming
钢铁研究学报(英文版)
Abstract： Pulverized coal injection (PCI) is a key technology in modern ironmaking by blast furnace (BF) and the life of injection lance has a great influence on PCI operation and on normal running of blast furnace. It is found that the main reasons for the failure of the lances are their outer surface oxidation and the inner surface erosion through monitoring some lances used in BF. The outer surface oxidation of the lances made of lCr18Ni9Ti is inevitable under high hot blast temperature condition through thermodynamics analysis. A mathematical model for calculating the temperature of common monocular coal lance had been developed according to the principles of mass and energy balance. Increasing temperature and flow velocity of the hot blast would cause a rise in the lance temperature. The influence of hot blast temperature is more obvious. The lance temperature would decline when compressed air flux increases. Conveying technology of dense phase pulverized coal is beneficial to extending lance′s life because decreasing solid-gas ratio would intensify erosion and burning loss. The anti-oxidation temperature of lance materials needs to be over 1000 ℃ for BF intensified smelting. In order to increase the resistance to oxidation of the coal lance′s outer surface, oxidation-resistant steel or Al coating stainless steel is the appropriate material for BF use. Employing the metal surface treatment technology to enhance the hardness of the coal lance′s internal surface could prolong the service life of coal lance.
关键词:
Key words: blast furnace
,
coal lance
,
failure mechanism
,
material requirements
金属学报
Volu扣ne 27SeriesB1991AUTHOR INDEX CCAO Guanghan(曹光旱)············……6一B科6CAo weijie(曹卫恋)..················……5一B32oCAO Yilin(曹益林)··················……6一B443CHANG Xin(常听)···············……1一B48CHE Guang邻n(车广灿)·············一6一B科0CHEN Erbao(陈二保)···············……6一B410CHEN Jia....
关键词:
Materials Research Bulletin
Through analysis of the latest experimental results reported in the literature and obtained in our laboratory, we have extended our previous quantum confinement/luminescence center model for the photoluminescence mechanism of porous Si and of nanometer-silicon-particle-embedded Si oxide films (G.G. Qin and Y.Q. Jia, Solid State Commun. 86, 559 (1993)). We consider that there are three main types of competitive photoexcitation/photoemission processes and that the process in which photoexcitation occurs in the nanometer silicon particles (NSPs) while photoemission occurs in the luminescence centers (LCs) in the SiOx layers very close to the NSPs is usually the major one. We discuss under what conditions the other two types of processes will dominate. We believe that the extended quantum confinement/luminescence center model is a physical model that is suitable for the photoluminescence from silicon oxide films embedded with NSPs or nanometer Ge particles (NGPs), as well as from oxidized porous Si. (C) 1999 Elsevier Science Ltd.
关键词:
oxides;luminescence;defects;blue-light emission;visible luminescence;optical-properties;nanocrystals;mechanism;dependence;sio2-films;absorption;spectra;defects
刘守平
,
周上祺
,
王佳眉
,
任勤
腐蚀学报（英文）
用金相显微镜、扫描电镜、X射线衍射仪和X射线能谱仪对天然气井油管悬挂器腐蚀失效进行了检测分析，并对天然气井油管悬挂器用35CrMo钢进行了盐雾试验，结果表明，天然气中的水和CO2是引起腐蚀的主要介质，腐蚀产物主要是FeCO3，高速天然气冲刷和钢中的非金属夹杂加剧了腐蚀的速度.
CORROSION FAILURE ANALYSIS OF AN OIL TUBE USED IN NATURAL GAS WELL
LIU Shou-ping,ZHOU Shang-qi,WANG Jia-mei,REN Qin
Chongqing University
A failed oil tube used in natural gas well was examined by optical microscope,scanning electron microscope ,X-ray diffractometer and X-ray spectrometer.Corrosion behavior of 35CrMo steel samples of the oil tube were investigated by means of salt spray tests in the laboratory.The results show that CO2 and H2O are primary factors in the corrosion of oil tube.The corrosion product is FeCO3,non-metallic inclusions in the steel and erosion of natural gas fluid played an important role in accelerating the corrosion.
oil tube;
natural gas well；
35CrMo steel；
failure analysis；
corrosion
关键词:
悬挂器
,
null
,
null
,
null
李凤娟
,
吕国光
金属世界
doi:10.3969/j.issn.1000-6826.2014.04.14
通过对烧结配料所需原料及对冷烧结矿成品检验采制样方法的分析，找出影响检验结果真实性的因素，采取有效的改进措施，使本钢原料厂一次配料、本钢炼铁厂265 m2烧结二次配料及265 m2烧结系统各项稳定率有了很大的提高，烧结矿实物质量和各项技术质量指标有了很大的进步，保证了高炉的稳定顺行。
提高本钢265 m2冷烧结矿及原料检验代表性的实践
Practice of Improving the 265 m2 Cold Sinter and Raw Material Inspection Representative
供稿|
李凤娟,吕国光/
LI Feng-juan, LV Guo-guang
DOI：10.3969/j.issn.1000-6826.2014.04.14
导读内容
本钢炼铁厂265 m2烧结机生产所需要的含铁原料比较复杂，一次配料料种较多，且烧结含铁原料是由本钢原料厂二车间供料，原料质量的不稳定，会影响烧结矿质量的提高和新一号高炉的强化及高炉技术指标的改善。本钢质量管理中心驻冷烧检查站加强了对烧结配料所需原料及对冷烧结矿成品检验采制样代表性的研究，采取了一些改进措施，达到了良好的效果。含铁料成分稳定率、烧结矿各项质量和技术指标在稳步地提高。下面，对本钢质量管理中心驻冷烧检查站就提高采样及检验过程的准确性所采取的措施和办法进行说明。
烧结矿采样是半自动采样，每两小时采样一次，作为一个批次，来代表整个2h烧结矿的成份。
关键词:
