材料期刊网

ELECTROCHEMICAL STUDIES ON ANODIC DISSOLUTION OF SYNTHETIC NICKEL SULFIDES

FANG Zhaoheng CHEN Jiayong Institute of Chemical Metallurgy , Academia Sinica , Beijing , China CHEN Jiayong Institute of Chemical Metallurgy , Academia Sinica , Zhongguancun , Beijing , China

金属学报(英文版)

The anodic behavior of synthetic nickel sulfides in sulfuric acid solutions was studied.When the anodes of Ni_3S_2 ,Ni_7S_6 and NiS are actively dissolved respectively,a solid layer forms on the electrode surface with its nature and composition depending on the potentials applied. Based on the electrochemical phenomena,phase and elemental compositions of the solid layer formed on the electrode surface were determined.The apparent number of electrons transfer- red during dissolution of Ni~(2+)was also measured.It can be considered that there are three parallel reactions ocurred on the electrode:the reaction with formation of HSO_4~- or SO_4~(2-), the reaction with formation of sulfides as intermediates and the reaction of Jorming elemental sulfur.With NiS_2 as an anode,formation of SO_4~(2-)or HSO_4~- can be considered as the only re- action occurred on the electrode.

关键词: nickel sulfide , null , null

Brief Outline of the Metallurgy Department of Kunming Institute of Technology

LIU Chunpeng Kunming Institute of Technology , Kunming 650093 , China.

材料科学技术（英文）

关键词:

Application of Microwave Radiation to Extractive Metallurgy

LIU Chunpeng XU Yousheng HUA Yixin Kunming Institute of Technology , Kunming , 650093 , China.

材料科学技术（英文）

In applying the microwave radiation to extractive me- tallurgy,it is essential first of all to find the extent of microwave energy absorbed by various minerals experi- mentally.In this paper,more than 25 kinds of common useful minerals have been individually irradiated by a 500 W,2450 MHz microwave source in an enclosed quartz crucible to ascertain their heating temperature in a definite time.In addition,the reduction and cbloridization tests were also carried out on the titanomagnetite concentrate and pentlandite with microwave heating,respectively. These experiments indicate potential applications of util- izing microwave energy in extractive metallurgy.

关键词: microwave radiation , null , null , null

Chen系统的状态变量周期性反馈控制

李开明 , 李亚洲 , 冯维贵 , 林长

量子电子学报 doi:10.3969/j.issn.1007-5461.2007.05.014

采用非线性反馈控制,用附加了带参数的正弦项对Chen系统进行了有效的控制.随着参数k的逐渐增大,系统的动力学行为呈现出一系列的变化.数值研究结果表明:随控制参数的增大,驱动信号的强度渐大,混沌系统由混沌运动到周期轨道,最终到一相点.

关键词: 混沌 , Chen系统 , 不动点 , Lyapunov指数 , 反馈控制

OXIDE METALLURGY-ITS PURPOSES AND PRACTICAL APPROACHES

Z. T. Ma and D. Janke(Institute of Iron and Steel Technology , Freiberg University of Mining and Technology , Germany)

金属学报(英文版)

Useder certain conditions, nonmctallic inclusions such as oxides, sulfides, nitrides and carbides are no longer harmful to sted service properties. With the new concept of oxide metallurgy, these properties can be improved by generating fine oxide inclusions which serve as heterogeneous nuclei for sulfide and fine ferrite[1-4]. A novel continuous casting (CC) process is expected to be created with the utilization of oxide metallurgy. This is also useful for the forthcoming technologies of direct rolling and near-net-shape casting. The main idea of oxide metallurgy consists of an alternative oxidation technology. It is based on steels treated by complex metals such as Ti, Zr, Ti-Zr alloys and rare earth metals. The selected deoxidants should follow the required conditions which are concluded in this paper.

关键词: oxide , null , null , null

Improvement of Ductility of Powder Metallurgy Titanium Alloys by Addition of Rare Earth Element

Yong LIU , Lifang CHEN , Weifeng WEI , Huiping TANG , Bin LIU

材料科学技术（英文）

Ti-4.5Al-6.0Mo-1.5Fe, Ti-6Al-1Mo-1Fe and Ti-6Al-4V alloys were prepared by blended elemental powder metallurgy (PM) process, and the effects of Nd on the microstructures and mechanical properties were investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). It was found out that the addition of Nd increased the density of sintered titanium alloys slightly by a maximum increment of 1% because small amount of liquid phase occurred during sintering. The addition of Nd shows little effect on the improvement of tensile strength, while the elongation is significantly improved. For example, the elongation of Ti-4.5Al-6.0Mo-1.5Fe can be increased from 1% without addition of Nd to 13% at a Nd content of 1.2 wt pct.

关键词: Powder metallurgy titanium alloy , null , null , null

Kunming Institute of Precious Metals

WANG Yonglu NING Yuantao Kunming Institute of Precious Metals , Kunming , China.

材料科学技术（英文）

关键词:

SYNTHESIS OF NANO-ZnO PARTICLES FOR ALUMINUM METALLURGY AS INERT ANODE MATERIAL

A.A.A. Saleh , Y. Fu , X.J. Zhai

金属学报(英文版)

Nano-ZnO particle was produced by evaporating zinc powders in air at air °ow-rate from 0.2 to 0.6m3/h. Nano-ZnO particles was formed by the oxidation of the evapo- rated zinc vapor. X-ray di®raction shows the powders to be ZnO with lattice parame- ters of a=0.3249nm and c=0.5205nm. The particle size is dependent upon the transit time from the source to the collection area. The size of particles was ranged between 81 to 103nm. The average density resulted was 4.865g/cm3. Normal ZnO and nano-ZnO were investigated to use them in aluminum metallurgy as an inert anode material. A certain amount of both oxides were molded subsequently inserted to the molten cryolite-aluminum oxide to investigate the corrosive behavior of both oxides. When the sintering temperature increased up to 1300±C, the weight loss ratio rose to 5.01%{7.33% and up to 7.67%{10.18% for nano-ZnO and normal ZnO, respectively. However, when the samples in the molten cryolite aluminum oxide were put for long time, the corrosive rate was found to be higher. It was found that the corrosive loss weight ratio of nano-ZnO anode was much lower than the normal one made from ordinary-ZnO providing that the nano-ZnO is more possible to be use inert anode material.

关键词: reactive evaporation method , null , null

Preparation of graphene by chemical vapor deposition

新型炭材料

Chemical vapor deposition (CVD) is an effective way for the preparation of graphene with large area and high quality. In this review, the mechanism and characteristics of the four main preparation methods of graphene are briefly introduced, including micromechanical cleavage, chemical exfoliation, SiC epitaxial growth and CVD. The recent advances in the CVD growth of graphene and the related transfer techniques in terms of structure control, quality improvement and large area graphene synthesis were discussed. Other possible methods for the CVD growth of graphene were analyzed including the synthesis and nondestructive transfer of large area single crystalline graphene, graphene nanoribbons and graphene macrostructures.

关键词: Graphene;Preparation;Chemical vapor deposition;Transfer;few-layer graphene;epitaxial graphene;large-area;carbon;films;surfaces;nickel;phase

Efficient growth of high-quality graphene films on Cu foils by ambient pressure chemical vapor deposition

Applied Physics Letters

We developed an ambient pressure chemical vapor deposition (CVD) for rapid growth of high-quality graphene films on Cu foils. The quality and growth rate of graphene films are dramatically increased with decreasing H(2) concentration. Without the presence of H(2), continuous graphene films are obtained with a mean sheet resistance of < 350 Omega/sq and light transmittance of 96.3% at 550 nm. Because of the ambient pressure, rapid growth rate, absence of H(2) and readily available Cu foils, this CVD process enables inexpensive and high-throughput growth of high-quality graphene films. (C) 2010 American Institute of Physics. [doi: 10.1063/1.3512865]

关键词: