DING Hua
,
LI Hua-ying
,
DING Hao
,
QIU Chun-lin
,
TANG Zheng-you
钢铁研究学报(英文版)
Two steels without and with Nb addition were chosen to investigate the effects of Nb on the microstructures and the mechanical properties of Fe-Mn-Al-Si steels. The results revealed that Nb refined the grains markedly and both TRIP and TWIP effects occurred during deformation process. The Nb containing steel possesses higher yield strength and much lower tensile strength, the latter being explained by the suppression of TRIP effect due to the increase of stacking fault energy. This indicates grain refining is secondary for strengthening of steels when TRIP or TWIP effect exists during the deformation of low carbon and high Mn steels.
关键词:
grain size
,
strength
,
high Mn steel
,
Nb
TANG Zhengyou
,
DING Hua
,
DU Linxiu
,
DING Hao
,
ZHANG Xin
钢铁研究学报(英文版)
In order to control retained austenite, the effect of hot deformation in the intercritical region on the microstructure of hotrolled transformationinduced plasticity (TRIP) steel was studied on a Gleeble 1500 hot simulator. Compressive strains varying in amounts from 0 to 60% were imposed in the intercritical region, and effects on the formation of polygonal ferrite, carbidefree bainite and retained austenite were determined. With increasing the hot deformation amount and the ferrite content and decreasing the carbidefree bainite content, the volume fraction of retained austenite decreases. Increased dislocation density, grain refinement of ferrite and carbon enrichment are the main factors which control retained austenite stability.
关键词:
TRIP steel;intercritical (α+γ) region;hot deformation;retained austenite
DING Hao
,
DING Hua
,
QIU Chunlin
,
TANG Zhengyou
,
ZENG Jianmin
,
YANG Ping
钢铁研究学报(英文版)
The mechanical property and forming limit experiments were carried out on a high manganese TRIP/TWIP steels with 18.8% manganese. And the forming limit diagram was obtained. This high manganese steel shows outstanding mechanical properties combining high strength and good formability. Its FLD0 is about 38%. The effects of conventional mechanical property on the FLD0 were analyzed. With the contents of Mn increasing, FLD0 increases, which indicates TWIP effect is advantageous to enhance formability. Combining with three classical models and volume invariable principle, a FLD model was established, which fits high manganese steels very well.
关键词:
high manganese TRIP/TWIP steel;mechanical properties;formability;forming limit diagram
杨文虎
,
易冉
,
徐阳
,
惠思思
,
曹晓珑
绝缘材料
doi:10.3969/j.issn.1009-9239.2012.01.014
研究了不同外施工频电压下环氧树脂绝缘中的电树枝结构、生长的特性,并用Ding等提出的模型解释了电树枝的发展过程,模拟了其生长曲线.结果表明:在同一电压下,环氧树脂中电树枝的生长速度基本为恒定值,随外施电压的升高,电树枝分枝变少,生长速度基本呈指数增加,且利用模型模拟的生长曲线与实验测试的结果吻合,最后讨论了模型的物理基础.
关键词:
电树枝
,
环氧树脂
,
劣化
,
动力学
,
模型
,
模拟
陈伟亮
,
张宁
,
唐昭辉
,
丁学勇
材料研究学报
将Miedema模型与实验数据相结合得到适于Miedema模型的O和S的参数(O:电负性7.04、电子密度6.03、摩尔体积4.59;S:电负性5.8、电子密度3.24、摩尔体积6.97),计算了141种O的二元化合物和145种S的二元化合物生成焓其平均绝对误差(MAPE)分别为36.8％、32.4％.结合Ding导出的三元系相互作用系数计算模型,计算了1873 K时Fe基熔体中O和S与其它元素之间的相互作用系数.与实验数据的比较表明,除个别元素外,计算值与实验值之间误差不大且变化趋势比较一致.将误差较大的Nb、Ag、Pt的电负性参数由原来的4.05、4.35、5.65修正为4.31、4.17、5.57,使用Miedema模型的计算精度有很大的提高.
关键词:
材料科学基础学科
,
Miedema模型
,
含O和S熔体与合金
,
相互作用系数
,
参数的修正
