S.B. Zhang and H. Nejishi (Department of Mechanical Engineering and Intelligent Systems
,
University of E feetro- Communications
,
Chofugaoka 1-5-1
,
Chofu-shi
,
Tokyo 182-8585
,
Japan)
金属学报(英文版)
In this paper local compressive deforming of a hexagonal tube of aluminum (JISA1050) is investigated by an electromagnetic forming. The hexagonal tubes are annealed for 1h. at 400℃, which have 55mm width with 1mm thickness, and 10mm corner edius. The deformed ation of the hexagonal tube, i.e., bead width, is 10, 15, 20mm, respectively. The magnetic flux density in the gap between the field shaper and the external surface of hexagonal tube is measured, and the result is that the magnetic flux density for a given voltage is almost identical along the gap) and decreases with increasing the gap. The profiles and the strain distribution of the hexagonal tube de- formed are affected by the change Of the charging voltage and the dimensions of a bead width. The greater compressive strum in the cireuwtrential direction is develOPed on plane part near corner,while tensile strain on the corner occurs. A metallic block is inserted inside the hexagonal tube so that uniform profile can be obtained. The simulation of the forming is performed by a finite-element method and compared with the experimental results.
关键词:
electromagnetic forming
,
null
,
null
,
null
,
null
Journal of Materials Research
Based on the best bulk metallic glass (BMG) forming alloy in the Mg-Cu-Y ternary system, we introduced Ag (or Ni) to partially substitute for Cu to improve the glass-forming ability (GFA). The objective of this paper is twofold. First, we illustrate in detail a recently developed search strategy, which was proposed but only briefly outlined in our previous publication [H. Ma, L.L. Shi, J. Xu, Y. Li, and E. Ma: Discovering inch-diameter metallic glasses in three-dimensional composition space. Appl. Phys. Lett. 87, 181915 (2005)]. The protocol to navigate in three-dimensional composition space to land large BMGs is spelled out step-by-step using the pseudo-ternary Mg-(Cu,Ag)-Y as the model system. Second, our ability to locate the best BMG former in the composition tetrahedron allows us to systematically examine, and conclude on, the effects of a given alloying element. The large improvement in glass-forming ability in the Mg-(Cu,Ag)-Y system relative to the based ternary will be contrasted with the reduced glass-forming ability in the Mg-(Cu,Ni)-Y pseudo ternary system. It is demonstrated that the improvement of glass-forming ability requires judicious choice of substitutional alloying elements and concentrations, rather than simple additions of multiple elements assuming the "confusion principle."
关键词:
bulk metallic-glass;shaped copper mold;amorphous-alloys;thermal-stability;ternary-system;casting method;p system;diameter;zr;mm
孙保基
,
张葆
,
宋策
,
龙思源
液晶与显示
doi:10.3788/YJYXS20163109.0921
针对TLD算法的特征点无法有效表述目标问题，提出了一种基于角点增强改进的TLD目标跟踪算法。改进算法在跟踪模块加入了对目标表述能力更强，具有光照不敏感性和旋转不变性的 Shi-Tomas 角点作为跟踪特征点。跟踪器运行时，在角点经光流法跟踪和双向误差检测后，利用剩余的稳定角点定位目标窗口。对照结果表明，改进算法在面对目标抖动和形变时可以稳定跟踪；有效抑制因跟踪平滑点造成的漂移现象；提高了跟踪的稳定性。针对 TLD算法跟踪过程中因在线模板积累造成的计算量持续增大、实时性持续降低的问题，提出了一种依据相似度中值的模板判断删除机制。该删除机制在模板积累到设定阈值时运行，根据模板与当前目标的相似度，删除不再具备代表性的模板；调整模板空间并更新模板数目。实验表明，该删除机制在应对模板更新快、持续时间长的跟踪情景时有效降低算法计算量，实时性可提高约20％。
关键词:
目标跟踪
,
TLD
,
角点特征
,
在线模板
