Qu Zhihao Shanghai Technical College of Metallurgy
,
Shanghai
,
China PENG Huihong shanghai Institute of Non-Ferrous Metals
,
Shanghai
,
China Shanghai Institute of Non-Ferrous Metals.Shanghai
,
China
金属学报(英文版)
A mixed method of solution for contact stresses on rollers was suggested by the combina- tion of similitude principle.photoelastic method,Hertz's contact theory and numerical calculation.Thus,not only the distribution regularity of axial contact pressure on roller of limited length,but also the three-dimensional solution of stresses in the contact po- sitions may be obtained.An actual example is presented in the paper.It shows that the practical damaged phenomenon in real roller is in agreement with the result of the analysis
关键词:
roller contact stress
,
null
,
null
LIU Chengjun
,
SHI Peiyang
,
ZHANG Dayong
,
JIANG Maofa
钢铁研究学报(英文版)
A great amount of ferrous tailings and slag cause severe damage to the ecological environment, which must be reclaimed and utilized. The composition, type, and characteristics of ferrous tailings and slag in China were introduced. The research status and the application outlook of glass ceramics made from ferrous tailings and slag were discussed. Glass ceramics made from ferrous tailings and slag can be applied to various fields, and it will be environmentally conscious materials in the 21st century.
关键词:
glass ceramics;ferrous tailings;slag
Electrochimica Acta
To investigate the corrosion protection mechanism of polyaniline (PANI) films on ferrous metals, this work presents preparation method of a separate protonated PANI film electrode and results of its open-circuit potential (OCP) in 0.5 M NaClO4 and 0.5 M Na2SO4 solutions with different pH and the galvanic interaction between the PANI film electrode and ferrous metals. X-ray photoelectron spectroscopy (XPS) shows the lower pH corresponds to higher protonation level of H+ in the film, and a more positive OCP of PANI film. The PANI film accelerated the corrosion of 20A carbon steel slightly with a PANI to steel area ratio less than 25: 1, while the PANI films maintained passivity for a ratio above to 25:1 for the 20A steel. For the coupling of 2Cr13 stainless steel/PANI, an equal area PANI film could maintain 2Cr13 in a passive state. The results suggest that corrosion protection of 20A carbon steel and 2Cr13 stainless steel by PANI film in the acid solution is due to passivity protection. The excess oxidative charge stored in the PANI and the equilibrium activity of protonated PANI with the acid environment provide a persistent driving force for carbon steel and 2Cr13 stainless steel passivity. (C) 2004 Elsevier Ltd. All rights reserved.
关键词:
protonated polyaniline;ferrous metals;open-circuit potential;galvanic;coupling;passivity;corrosion protection;mild-steel;coatings;behavior
Materials and Corrosion-Werkstoffe Und Korrosion
In order to investigate the galvanic anodic protection (GAP) of ferrous metals (such as 410, 304 and 316 stainless steels) in acid solutions by doped polyaniline (PANi), separate doped PANi powder-pressed electrodes with different surface areas (the area ratio of the PANi electrode to stainless steel is between 1:1 and 1:2) have been prepared. These were coupled with ferrous metal in the following solutions: 5 M sulphuric acid, 5 M phosphoric acid and industrial phosphoric acid (containing 5 M phosphoric acid and 0.05% chloride ion) to construct a galvanic cell, in which PANi is cathode while ferrous metal is anode. The results indicate that a PANi electrode with sufficient area can provide corrosion protection to stainless steel in these acidic solutions. A pilot scale coupling experiment was carried out. The results indicate that PANi is a promising material as an electrode for the anodic protection of ferrous metals in acidic solutions in industrial situations.
关键词:
conducting polymer-coatings;corrosion protection;stainless-steel;spectroscopy;passivation;performance;mechanism;behavior;primers;films
Acta Materialia
In a first report [Jin ZH.. Gumbsch P, Ma E, Albe K, Lu K, Hahn H, et al. Scripta Mater 2006;54:1163], interactions between screw dislocation and coherent twin boundary (CTB) were studied via molecular dynamics simulations for three face-centered cubic (fcc) metals, Cu, Ni and Al. To complement those preliminary results, purely stress-driven interactions between 60 degrees non-screw lattice dislocation and CTB are considered in this paper. Depending on the material and the applied strain, slip has been observed to interact with the boundary in different ways. If a 60 degrees dislocation is forced by an external stress into a CTB, it dissociates into different partial dislocations gliding into the twin as well as along the twin boundary. A sessile dislocation lock may be generated at the CTB if the transited slip is incomplete. The details of the interaction are controlled by the material-dependent energy barriers for the formation of Shockley partial dislocations from the site where the lattice dislocation impinges upon the boundary. (c) 2007 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
关键词:
dislocation;slip;twinning;twin grain boundary;molecular dynamics;molecular-dynamics simulation;grain-boundaries;nanocrystalline;materials;cross-slip;rate sensitivity;deformation;copper;strength;aluminum;fcc
ZHANG Xiumu LI Yiyi Institute of Metal Research
,
Academia Sinica
,
Shenyang 110015
,
China
金属学报(英文版)
In situ observations of the nucleation and growth of ferrous martensites,including ε-, lenticular,butterfly,thin-plate and composite-plate ones at low temperature stage on optical or transmission electron microscope were carried out.The results confirmed the faulting model for the formation of ε-martensite proposed by Olso and Cohen.The grain boundaries and tri- ple points are the favourable nucleation sites for the thin plates,and their surface relief grown initially like a small needle.The lenticular martensite was observed as two stages of formation.According to the dislocation resolving reaction. (a/6)[111]_b→(a/3)[]_b+(a/2)[111]_b,the emission dislocation(=(a/2)[111]_b)acting as the dislocation source for the transition of lattice invariant shear from twinning to slip was proposed.
关键词:
martensite
,
null
,
null
,
null
,
null
B.W. Wang
,
H. Shen
金属学报(英文版)
Ni-Cr System solar selective thin solid films were prepared by d.c. magnetron reactivesputtering under the atmosphere of O2 and N2. Ni-Cr alloy was chosen as targetmaterial and copper sheets as substrate. Using SEM, Spectrophotometer and Talystepto analyze the relations between the selective characteristic and the structure, theformation and the thickness of the thin films. The aim is to obtain good solar selectivethin films with high absorptance and low emittance, which is applied to flat plate solarheat collectors.
关键词:
solar selective thin film
,
null
,
null
,
null
