WANG Qingfeng
,
CHAI Feng
,
CAI Jianwei
,
PAN Tao
,
SU Hang
钢铁研究学报(英文版)
The kinetics of εCu particle dissolution in the matrix of heat affected zone (HAZ) during welding of a coppercontaining steel was determined by assembling the welding temperaturetime program into a modified Whelan′s solution. The particle dissolution dependence on the degree of “superheating” above the equilibrium transformation is demonstrated from the model. In terms of volume fraction of particle dissolution, the HAZ may be classified into three zones, including the undissolving zone, the partially dissolving zone, and the completely dissolving zone, respectively. The numerical solution was in good agreement with the experimental examination finding. The results of model can be used to quantitatively map the εCu dissolution zone dependence on the peak temperature of welding thermal cycles and understand the evolution of this transformation during welding.
关键词:
εCu;particle dissolution;kinetics;welding;steel
WANG Qingfeng
,
SHANG Chengjia
,
CHEN Dawei
,
CAI Jianwei
,
CHEN Weichang
钢铁研究学报(英文版)
The kinetics of εCu particles dissolution in the matrix during welding of a copperprecipitation strengthening steel was determined by a combination of GleebleTM physical simulation, TEM examination and hardness measurement. The εCu particles underwent a coarsening and part dissolution and then complete dissolution reaction as the peak temperature increased from 750 to 1 000 ℃, which resulted in the decrease in the number density of εCu particles and hardness in the heataffected zone (HAZ). The results can be used to understand the evolution of this transformation and a softening behavior of the HAZ during welding of this type of steel.
关键词:
εCu particle dissolution;hardness;kinetics;steel;welding;physical simulation
张宝艳
,
陈祥宝
,
李敏
,
邢丽英
,
汪亮
,
蒋诗才
航空材料学报
doi:10.3969/j.issn.1005-5053.2002.01.008
探讨了树脂基体、碳纤维增强体以及树脂基体-纤维的界面等对双马来酰亚胺(简称双马)树脂基复合材料冲击后压缩强度(CAI)值的影响,指出降低树脂基体的交联密度和产生微观两相结构是提高碳纤维/双马复合材料CAI值的两个典型方法.合适的树脂含量有利于保持复合材料体系较高的CAI值,采用高强高韧性的碳纤维可明显提高复合材料体系的CAI值.为获得较高的CAI值,保持合适的树脂基体-纤维界面性能也是必要的.
关键词:
双马来酰亚胺
,
纤维增强复合材料
,
韧性
,
界面
X.B. Tian
,
X.F. Wang
,
A.G. Liu
,
L.P. Wang
,
S. Y. Wang
,
B. Y. Tang and P. K. Chu 1)Advanced Welding Production & Technology National Key Laboratory
,
Harbin Institute of Technology
,
Harbin 150001
,
China 2)Department of Physics & Materials Science
,
City University of Hong Kong
,
China
金属学报(英文版)
The research on plasma immersion ion implantation has been conducted for a little over ten years. Much is needed to investigate including processing technlogy, plasma sheath dynamics, interaction of plasma and surface, etc. Of the processing methods elavated temperature technique is usually used in PIII to produce a thick modified layer by means of the thermal diffusion. Meanwhile plasma ion heating is more recently developed by Ronghua Wei et al[1]. Therefore the temeperature is a critical parameter in plasma ion processing. In this paper we present the theoretical model and analysize the effect of imlantation voltage, plasma density, ion mass,etc on the temperature rise.
关键词:
plasma immersion ion implantation
,
null
,
null
夏小建
量子电子学报
doi:10.3969/j.issn.1007-5461.2009.06.010
采用Wei-Norman方法,求出含时变电压源的介观LC电路随时间演化的精确解,应用相空间准概率分布函数,研究了时变电源作用下介观LC电路相干态的量子特性,结果表明此函数是一个二维运动的Gauss波包,其中心电量和磁通呈余弦和正弦变化.
关键词:
量子光学
,
LC回路
,
介观电路
,
相干态
,
量子态演化
,
相空间的准概率分布函数
段友社
,
郭书良
,
吴刚
,
侯军生
复合材料学报
基于热压罐成型工艺,选择了树脂柱Z向增强泡沫芯材、碳纤维Z向增强泡沫芯材、Kevlar纤维缝纫增强泡沫芯材3种Z向增强复合材料结构,对夹芯结构进行了低速冲击损伤和冲击后压缩（CAI）性能研究,考察了不同Z向增强方式对冲击损伤面积和破坏模式的影响。结果表明,Z向增强对泡沫芯材产生了初始损伤,其冲击后损伤面积大于未增强泡沫夹芯结构;但Z向增强改变了夹芯结构的压缩破坏机制。通过选用合适的Z向增强材料和Z向增强参数,能够提高夹芯结构的压缩强度和CAI强度。其中当增强材料为碳纤维,增强参数为10mm×10mm时,压缩强度提高了13%,CAI强度提高超过40%。
关键词:
复合材料
,
泡沫夹芯
,
Z向增强
,
冲击损伤
,
冲击后压缩
徐菊良
,
邓博
,
孙涛
,
李劲
,
蒋益明
金属学报
doi:10.3724/SP.J.1037.2009.00598
利用Thermo-Calc软件并结合金相显微镜,定性研究了2205双相不锈钢在800℃下敏化不同时间后的微观组织演变过程.通过研究扫描速率、介质成分、介质温度和试样表面状态优化了双环电化学动电位再活化法(DL-EPR),并用该优化方法研究了2205双相不锈钢晶间腐蚀敏感性.结果表明:DL-EPR法能定量评价σ相对2205双相不锈钢晶间腐蚀敏感性的影响,随敏化时间延长,σ相含量增多,晶jian 腐蚀敏感性也随之增加.腐蚀形貌的观测验证了这一规律,
关键词:
2205双相不锈钢
,
DL-EPR
,
晶间腐蚀敏感性
,
σ相
