赵显武
,
褚武扬
,
宿彦京
,
高克玮
,
乔利杰
金属学报
doi:10.3321/j.issn:0412-1961.2005.07.007
研究了不同极化状态下PZT-5H铁电陶瓷压痕裂纹在应力和电场单独作用以及耦合作用下的扩展行为.结果表明,压痕裂纹残余应力引起的应力场强度因子近似等于断裂韧性.对沿长度方向极化的试样,正、负电场均能引起压痕裂纹的扩展,但正电场的作用更大.电场和应力的耦合作用表现为对应力的线性叠加.电场引起的内应力σin=(φ)YE/[1.16(1-v2)EC],式中(4)=(2.75-5.71)×10-4,与PZT的极化状态有关.
关键词:
PZT铁电陶瓷
,
压痕裂纹
,
应力和电场耦合
Journal of Physics-Condensed Matter
This research purposes to investigate the atomic and electronic structures of the Al/TiC(001) interface with lattice misfit using the ab initio pseudopotential approach. A detailed analysis of the relaxed atomic structure reveals that the atoms over the initial unfavourable sites relax to the favourable sites along the lateral plane. The properties of the semicoherent interface can be taken as averages over the different coherent sites. In addition, the interface atoms in relatively favourable regions are dragged near to the interface, while those in unfavourable regions are pushed away from the interface. Therefore, a large war-ping near the interface is made perpendicular to the lateral plane. The calculated adhesions explain the different wetting results from the viewpoint of structural transition. The subsequent analysis of electronic properties demonstrates that adhesions dominate mainly via the strong Al-C covalent bond.
关键词:
first-principles;1st principles;adhesion;surfaces;misfit;1st-principles;wettability;al
X. Q. Yang
,
L. X. Huo
,
Y. F. Zhang and J. X. Yan (School of Material Science and Engineering
,
Tianjin University
,
Tianjin 300072
,
China)
金属学报(英文版)
The buckling formation and influence factors during welding thin - plated structures were investigated based on finite element methods, An engineering treatment method for prdicating the buckling distor- tion was proposed in here. It was used the equivalent applied thermal - load to simulate the welding residual stress,therefore the calculation of complex welding distoriton can be transformed into 3D elas- tic structural applied- load analyses, which can reduce the quantities of calculating works effectively. The validation of the method was verified by comparison of the numerical simulation and experimental results. The simulation of buckling distorition for side - walled structrues of paseenger train was per- formed and the calculation was in agreement with measuring results in general. It was shown that the main factors for producing the buckling were the intermittent fillet and ping the during welding the stiffened beams and columns to the panel.The existence of the free edge of panels would reduce the crit- ical buckling stress and enlarge the deflection obviously,but the continuous weld in closed frames didn' t degrade the buckling situation.
关键词:
welding buckling distortion
,
null
,
null
陈嘉良
,
李万捷
高分子材料科学与工程
单体丙烯酰胺(AM)和甲基丙烯酰氧乙基三甲基氯化铵(DMC)通过2,2'-偶氮(2-脒基丙烷)二氢氯化物(V-50)引发,在紫外光的作用下合成P(AM-co-DMC)共聚物.通过毛细管膨胀计法测定了其反应动力学.随着单体浓度、引发剂浓度、反应温度的升高,反应速率也随之增加.在控制低转化率的条件下,以Fineman-Ross、Kelen-Tudos及Ye2rielevBrokhina-Roskin法计算了单体竞聚率.得出了在紫外光与引发剂共同作用下,AM和DMC共聚单体的反应级数为2.2502,引发剂的反应级数为0.5032,反应活化能为38.1920kJ/mol,AM和DMC的竞聚率分别为2.3398和0.2849.
关键词:
共聚
,
动力学
,
竞聚率
,
紫外光
,
丙烯酰胺
Z.L. Ding
,
Y.C. Fan
,
H.B. Qi
,
D.L. Ren
,
J.B. Guo and Z.Q. Jiang Shijiazhuang Railway Institute
,
Shijiazhuang 050043
,
China
金属学报(英文版)
The SiC_p/Al-alloy composite front broke rotors designed for SHANGHAI SANTANA cars were prepared by semi-solid stirring+liquid for ping process. The properties of the composite rotors were examined. The composite brake rotors were subjected to dynamometer tests on a SCHENCK broke testing system, referring to TLll0 standard of VOLKSWAGEN Company. The friction coefficient and thermal response during fade testing and the wear performance of the composite rotors were studied as the function of various parameters, such as braking pressures, initial speeds, initial temperatures, torque and decelerations, and compared with that of conventional cast iron rotors. The results showed that the properties of SiC_p,/Al-alloy composite rotors can achieve the requirements of commercial cast iron rotor.s. The results also suggested that the friction coefficients of composite rotors under different broking conditions are within the deviation band specified by the TLll0 standard, and the temperature rise of the composite rotors at the cud of each fade stop is lower than that of the cast iron rotors. The wear resistance of composite rotors was higher than that of cast iron rotors. The friction and wear mechanism are analyzed.
关键词:
SiC_p/Al-alloy composite
,
null
,
null
,
null
钱鹏
,
李兴华
量子电子学报
doi:10.3969/j.issn.1007-5461.2015.06.008
基于量子信道加密原理,结合Ping-Pong协议控制模式和信息模式的概念,提出了一个量子安全直接通信协议.在此协议中,发送者和接收者用n对Bell态作为量子信道,发送者用controlled-Not操作将单粒子纠缠入量子信道,接收者用controlled-Not操作将单粒子与量子信道解纠缠.通信双方依次执行控制模式和信息模式,控制模式检测窃听,信息模式发送秘密信息.控制模式和信息模式均不会对已建立的量子信道造成破坏,因此建立量子信道的过程仅需执行一次,此后通信双方可以反复进行控制模式和信息模式,从而不断进行窃听检测和秘密信息传输.
关键词:
量子光学
,
量子安全直接通信
,
信道加密
,
窃听检测
Journal of Applied Physics
Using the full potential linearized augmented plane wave method based on the spin density functional theory, we investigate the ferromagnetic properties, the electronic structure, and the formation energy of Ga(0.9375)M(0.0625)N (M=vacancy, Ca). The calculations indicate that both cases prefer ferromagnetic ground state. The magnetic moments mainly come from the N atoms surrounding the defect centers, which are different from the conventional diluted magnetic semiconductor. High formation energy for the Ga vacancy Suggests that the defect concentration is too low to result in the ferromagnetic GaN. The formation energy for the two substitutional (Ca(Ga),Ca(N)) and two interstitial sites (tetrahedral T, Ca(i-T) and octahedral O, Ca(i-O)) doped configurations indicates that Ca prefers the substitutional Ga in GaN. The defect concentrations for the Ga(0.9375)Ca(0.0625)N under thermal equilibrium N-rich and N-realistic growth conditions are also discussed, respectively. The calculations show that defect concentration under N-rich condition can readily reach 7%, while under N-realistic growth condition, the maximum defect concentration is as low as 1.71% when the growth temperature increases to 1100 K (melting point of GaN). These results suggest that it would be a little difficult to achieve ferromagnetic state for Ga(0.9375)Ca(0.0625)N using the chemical-equilibrium fabrication method, such as chemical precipitation. Using the same method as that for Cu-doped ZnO [L. H. Ye et al., Phys. Rev. B 73, 033203 (2006)], the transition temperature of Ga(0.9375)Ca(0.0625)N may be close to room temperature. (C) 2008 American Institute of Physics.
关键词:
generalized gradient approximation;doped zno;gan;semiconductors;calcium;systems;origin
刘守平
,
周上祺
,
王佳眉
,
任勤
腐蚀学报（英文）
用金相显微镜、扫描电镜、X射线衍射仪和X射线能谱仪对天然气井油管悬挂器腐蚀失效进行了检测分析，并对天然气井油管悬挂器用35CrMo钢进行了盐雾试验，结果表明，天然气中的水和CO2是引起腐蚀的主要介质，腐蚀产物主要是FeCO3，高速天然气冲刷和钢中的非金属夹杂加剧了腐蚀的速度.
CORROSION FAILURE ANALYSIS OF AN OIL TUBE USED IN NATURAL GAS WELL
LIU Shou-ping,ZHOU Shang-qi,WANG Jia-mei,REN Qin
Chongqing University
A failed oil tube used in natural gas well was examined by optical microscope,scanning electron microscope ,X-ray diffractometer and X-ray spectrometer.Corrosion behavior of 35CrMo steel samples of the oil tube were investigated by means of salt spray tests in the laboratory.The results show that CO2 and H2O are primary factors in the corrosion of oil tube.The corrosion product is FeCO3,non-metallic inclusions in the steel and erosion of natural gas fluid played an important role in accelerating the corrosion.
oil tube;
natural gas well；
35CrMo steel；
failure analysis；
corrosion
关键词:
悬挂器
,
null
,
null
,
null
但永平
,
彭红涛
,
王东云
,
刘芳华
液晶与显示
doi:10.3788/YJYXS20132801.0099
在图像处理中图像数据交换量大,图像数据传输是图像采集处理系统的关键环节.EDMA是DSP中用于实现数据快速交换的重要技术,具有独立于CPU的后台批量数据传输的能力.文章基于TI公司TMS320DM642芯片的图像采集处理系统,利用EDMA的数据传输方式实现视频数据信号高速实时传输.介绍了DSP的外部存储器接口与FPGA的FIFO存储器有机结合进行数据传输,分析了其设计的整体结构与逻辑控制的功能,并着重分析了基于EDMA Ping-Pong数据传输方式的原理及其应用.另外,EDMA中断服务程序调用CPU对已搬移完成的图像数据块进行处理,不仅提高了数据的传输效率,而且节约了CPU资源,使DSP的高性能得到了充分发挥,从而为视频信号处理的实时性奠定了基础.
关键词:
EDMA
,
DSP
,
FIFO
,
数据传输
,
Ping-Pong
