王其坤
,
胡海峰
,
陈朝辉
,
张玉娣
,
罗征
稀有金属材料与工程
针对2D C/SiC复合材料存在碳布层间缺乏纤维增强,层间结合较差的问题,提出通过Z-向穿刺工艺提高碳布层间结合,克服材料使用时可靠性不高的问题,并比较了穿刺工艺对复合材料微观结构和力学性能的影响.结果表明,通过Z-向穿刺工艺制得试样2D C/SiC-Z_(pin)的弯曲强度、弯曲模量和剪切强度分别为247.8 MPa、37.8 GPa和32.1 MPa,而未穿刺试样2D C/SiC的弯曲强度、弯曲模量和剪切强度分别只有219.3 MPa、34.4 GPa和23.3 MPa,由此可见,采用Z-向穿刺工艺能明显提高复合材料的力学性能.微观结构分析认为,试样力学性能提高的根本原因在于采用Z-向穿刺纤维加强了碳布层间结合,使材料具有较好的整体性,克服了复合材料层间结合较弱对力学性能带来的不利影响.
关键词:
2D
,
C/SiC
,
Z-向穿刺
,
微观结构
,
力学性能
叶龙海
,
邓琼
,
汤忠斌
复合材料学报
采用Hopkinson压杆试验装置,对2D-C/SiC复合材料进行了低温条件下的Z向动态压缩性能试验研究,低温条件通过控制酒精和液氮的配比系数得到,通过改变波形整形器几何尺寸的方法来实现恒应变率加载,以得到准确、可信的试验结果.试验结果表明:由于复合材料内部含有大量初始微缺陷,2D-C/SiC复合材料在低温动态加载条件下呈现伪塑性行为,其破坏时并未表现出典型的脆性破坏,而是在应力达到压缩强度时出现了显著的应变软化现象,在经历了较大的变形后才最终破坏.随着温度的降低,复合材料的动态Z向压缩强度增加,但失效应变减小.2D-C/SiC复合材料在低温环境下,其内部纤维和基体之间界面结合力增强,同时强的界面结合力可以导致高的压缩强度.
关键词:
陶瓷基复合材料
,
Hopkinson压杆试验装置
,
低温
,
动态Z向压缩力学性能
,
界面强度
Philosophical Magazine
The error of Equation (15b) in my article [Z.D. Zhang, Phil. Mag. 87 (2007) p.5309] in the application of the Jordan-Wigner transformation does not affect the validity of the putative exact solution, since the solution is not derived directly from that equation. Other objections of Perk's comment [J.H.H. Perk, Phil. Mag. 89 (2009) p.761] are the same as those in Wu et al.'s comments [F.Y. Wu et al., Phil. Mag. 88 (2008) p.3093; p.3103], which do not stand on solid ground and which I have sought to refute in my previous response [Z.D. Zhang, Phil. Mag. 88 (2008) p.3097]. The conjectured solution can be utilized to understand critical phenomena in various systems, whereas the conjectures are open to rigorous proof.
关键词:
3D Ising model;exact solution;conjecture;critical phenomena;ferromagnetism;magnetic phase transition;model;analyticity
Pan Ting
,
Song Wenjing
,
Cao Xiaodong
,
Wang Yingjun
材料科学技术（英文）
doi:10.1016/j.jmst.2016.01.007
Gelatin/Alginate hydrogels were engineered for bioplotting in tissue engineering. One major drawback of hydrogel scaffolds is the lack of adequate mechanical properties. In this study, using a bioplotter, we constructed the scaffolds with different pore architectures by deposition of gelatin/alginate hydrogels layer-by-layer. The scaffolds with different crosslinking degree were obtained by post-crosslinking methods. Their physicochemical properties, as well as cell viability, were assessed. Different crosslinking methods had little influence on scaffold architecture, porosity, pore size and distribution. By contrast, the water absorption ability, degradation rate and mechanical properties of the scaffolds were dramatically affected by treatment with various concentrations of crosslinking agent (glutaraldehyde). The crosslinking process using glutaraldehyde markedly improved the stability and mechanical strength of the hydrogel scaffolds. Besides the post-processing methods, the pore architecture can also evidently affect the mechanical properties of the scaffolds. The crosslinked gelatin/alginate scaffolds showed a good potential to encapsulate cells or drugs.
关键词:
Bioplotting
,
Tissue engineering
,
Scaffolds
,
Gelatin
,
Alginate
F.Q.Tian
金属学报(英文版)
Welded joint is a mechanical heterogeneous body, and mechanical heterogeneity has great effect on dynamic fracture behaviour of welded joints. In the present investigation, dynamic response curve and dynamic J-integral of practical undermatched welded joint and whole base and whole weld three-point-bend (TPB) models containing longitudinal crack are computed. Dynamic J-integral is evaluated using virtual crack extension (VCE) method and the computation is performed using MARC finite element code. Because of the effect of inertia,dynamic load response curve of computed model waves periodically. Dynamic J-integral evaluated by VCE method is path independent. The effect of inertia has little influence on dynamic J-integral curve. The value of dynamic J-integral of undermatched welded joint is lower than that of whole base metal and higher than that of whole weld metal. The results establish the foundation of safety evaluation for dynamic loaded welded structures.
关键词:
virtual crack extension
,
null
,
null
D.Han
,
S.R.Qiao
,
M.Li
,
J.T.Hou
,
X.J.Wu
金属学报(英文版)
The differences of tension-tension fatigue and tensile creep characters of 2D-C/SiC and 3D-C/SiC composites have been scrutinized to meet the engineering needs. Experiments of tension-tension fatigue and tensile creep are carried out under vacuum high temperature condition. All of the high temperature fatigue curves are flat; the fatigue curves of the 2D-C/SiC are flatter and even parallel to the horizontal axis. While the tension-tension fatigue limit of the 3D-C/SiC is higher than that of the 2D-C/SiC, the fiber pullout length of the fatigue fracture surface of the 3D-C/SiC is longer than that of the 2D-C/SiC, and fracture morphology of the 3D-C/SiC is rougher, and pullout length of the fiber tows is longer. At the same time the 3D-C/SiC has higher tensile creep resistance. The tensile curve and the tensile creep curve of both materials consist of a series of flat step. These phenomena can be explained by the non-continuity of the damage.
关键词:
2D-C/SiC
,
null
,
null
Mehdi Ebrahimian-Hosseinabadi Fakhredin Ashrafizadeh Mohammadreza Etemadifar Subbu S. Venkatraman
材料科学技术（英文）
In this paper, preparation of nano-biphasic calcium phosphate (nBCP), mechanical behavior and load-bearing of poly (lactide-co-glycolide) (PLGA) and PLGA/nBCP are presented. The nBCP with composition of 63/37 (w/w) HA/β-TCP (hydroxyapatite/β-tricalcium phosphate) was produced by heating of bovine bone at 700°C. Composite scaffolds were made by using PLGA matrix and 10-50 wt% nBCP powders as reinforcement material. All scaffolds were prepared by thermally induced solid-liquid phase separation (TIPS) at -60°C under 4 Pa (0.04 mbar) vacuum. The results of elastic modulus testing were adjusted with Ishai-Cohen and Narkis models for rigid polymeric matrix and compared to each other. PLGA/nBCP scaffolds with 30 wt% nBCP showed the highest value of yield strength among the scaffolds. In addition, it was found that by increasing the nBCP in scaffolds to 50 wt%, the modulus of elasticity was highly enhanced. However, the optimum value of yield strength was obtained at 30 wt% nBCP, and the agglomeration of reinforcing particles at higher percentages caused a reduction in yield strength. It is clear that the elastic modulus of matrix has the significant role in elastic modulus of scaffolds, as also the size of the filler particles in the matrix.
关键词:
Scaffold
Liubing WANG
金属学报(英文版)
Tests under mechanical strain control were performed to investigate the TMF behavior of Z2CND18.12N within the temperature range between 150-550℃. Different strain amplitudes and phase-angles were applied. Total strain controlled low cycle fatigue test was also performed at the peak temperature of TMF cycling. The results show that the cyclic stress response of the material displayed an initial hardening regime followed by a saturation period and then cyclic softening till failure. The TMF cycling leads to the development of significant amounts of mean stress. Some life prediction models were employed to predict the TMF life of Z2CND18.12N, and the results indicate that the energy-based models provide good prediction on the thermal-mechanical fatigue behaviors of this material. An optical microscopic observation shows that the surface crack initiations and crack propagations are typically transgranular mode.
关键词:
Thermomechanical fatigue
