Erlin ZHANG
,
Yunxue JIN
,
Songyan ZENG
,
Zhaojun ZHU
材料科学技术（英文）
TiB reinforced titanium composites have been successfully synthesized by adding the Al/TiB2 master alloy into titanium alloy. The phase constituent and the microstructure have been studied by XRD and SEM. Compared with the standard values, the lattice parameter of TiB calculated from the XRD pattern indicates that the synthesized TiB is of prefect crystal structure. The microstructure has shown that high aspect ratio fibrous TiB has been found, which homogeneously distribute in the matrix in a random way. The size is about 100 μm in length, less than 2.5 μm in diameter and the aspect ratio is greater than 40. Deep etched microstructures show that some coarse hollow TiB corresponding to primary TiB are also formed with smooth and flat surface and random transverse section. The size is about 100 μm in length and greater than 10 mum in diameter. The solidification process has also been analyzed.
关键词:
Bo YANG
,
Erlin ZHANG
,
Yunxue JIN
,
Zhaojun ZHU
,
Songyan ZENG
材料科学技术（英文）
TiC reinforced titanium composites has been produced with different Al content and C content by XDTM. The results have shown that TiC particles are of two different morphologies f coarse dendritical primary TiC and short bar-shape eutectic TiC. Al content has great effects on the morphology of TiC. With the increasing of Al content, the morphology of primary TiC changes from coarse developed dendrite into short bar-shape or plate--shape TiC with 35%Al. Meanwhile, the structure of the matrix changes from single Ti to Ti and Ti2Al and to Ti3Al. However, the C content has no influence on the microstructure of matrix. When the C content is less than 1.2%, the dendrite TiC disappears and only short bar-shape or plate-shape TiC exists in the composites. In addition, the effect of heat of heat treatment on the morphology of TiC has also studied.
关键词:
Journal of Applied Physics
Based on the developed multiple-scattering theory [C.-W. Nan and F. S. Jin, Phys. Rev. B 48, 8578 (1993)], an effective-medium theory (EMT) is proposed to treat coupled electromechanical behavior in composite media. The explicit relations for determining effective behavior of piezoelectric composites are derived. To illustrate the technique, numerical results of piezoelectric ceramic/epoxy composites for various particle shapes are presented over the whole range of concentrations. The EMT estimates are shown to be in good agreement with available experimental results. Porous piezoelectric ceramics are also discussed. The EMT predicts a similar critical behavior for heterogeneous piezoelectric materials to recent experiments.
关键词:
electromechanical properties;ceramics
Acta Materialia
In a first report [Jin ZH.. Gumbsch P, Ma E, Albe K, Lu K, Hahn H, et al. Scripta Mater 2006;54:1163], interactions between screw dislocation and coherent twin boundary (CTB) were studied via molecular dynamics simulations for three face-centered cubic (fcc) metals, Cu, Ni and Al. To complement those preliminary results, purely stress-driven interactions between 60 degrees non-screw lattice dislocation and CTB are considered in this paper. Depending on the material and the applied strain, slip has been observed to interact with the boundary in different ways. If a 60 degrees dislocation is forced by an external stress into a CTB, it dissociates into different partial dislocations gliding into the twin as well as along the twin boundary. A sessile dislocation lock may be generated at the CTB if the transited slip is incomplete. The details of the interaction are controlled by the material-dependent energy barriers for the formation of Shockley partial dislocations from the site where the lattice dislocation impinges upon the boundary. (c) 2007 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
关键词:
dislocation;slip;twinning;twin grain boundary;molecular dynamics;molecular-dynamics simulation;grain-boundaries;nanocrystalline;materials;cross-slip;rate sensitivity;deformation;copper;strength;aluminum;fcc
曹春海
,
杨名
,
张世远
,
杨森祖
,
崔旭高
,
尤立星
,
吉争鸣
,
康琳
,
许伟伟
低温物理学报
doi:10.3969/j.issn.1000-3258.2003.03.002
采用Nd0.7Sr0.3MnO3/SrTiO3/YBa2Cu3O7-δ的异质结构,研究了自旋极化准粒子的注入效应.在56μm宽的YBCO膜条上成功地制备了与超导膜条同样宽度但不同长度的六个注入结区,长度L分别为80μm, 40μm, 20μm, 10μm, 5μm和2μm.80nm厚的YBCO薄膜在16K温度下Jc为2×105A/cm2.Iin=0.5mA的自旋电流注入下,随L从80μm逐渐顺次减小时,注入效率η=ΔJc/ΔJin逐渐增大.而当L≤20μm后,η不再增加,达到几乎相同的值(～6).初步分析认为这与自旋极化准粒子在超导膜内的有效自旋扩散长度有关.异质结构中YBCO薄膜的超导电性以及注入窗口的尺寸对获得大的自旋注入效率十分重要.
关键词:
注入效率
,
自旋准粒子
,
巨磁阻
,
异质材料
