材料期刊网

Improvement of Weld Quality Using a Weaving Beam in Laser Welding

Xudong ZHANG , Wuzhu CHEN , Gang BAO , Lin ZHAO

材料科学技术（英文）

This paper describes a way to improve the weld quality through suppressing the porosity formation and restraining the growth of columnar grains by using a weaving beam in laser welding. The experimental results show that the N2 porosity of beam-weaving laser welding low carbon steel can be remarkably reduced with increasing weaving frequency, and porosity can be eliminated when the weaving amplitude is only 0.5 mm; and the Ar porosity in the weld metal is decreased with increasing weaving frequency and amplitude when the welding speed is higher than 0.5 m/min. The beam-weaving laser welding of ultra-fine grained steel has been investigated. The experimental results show that beam-weaving laser welding with appropriate amplitude and frequency can partly restrain the growth of the columnar grain and improve the tensile strength of the weld metal.

关键词: Welding , null , null , null

Microstructures and Toughness of Weld Metal of Ultrafine Grained Ferritic Steel by Laser Welding

Xudong ZHANG , Wuzhu CHEN , Cheng WANG , Lin ZHAO , Yun PENG , Zhiling TIAN

材料科学技术（英文）

3 mm thick 400 MPa grade ultrafine grained ferritic steel plates were bead-on-plate welded by CO¬2 laser with heat input of 120~480 J/mm. The microstructures of the weld metal mainly consist of bainite, which form is lower bainite plates or polygonal ferrite containing quantities of dispersed cementite particles, mixed with a few of low carbon martensite laths or ferrite, depending on the heat input. The hardness and the tensile strength of the weld metal are higher than those of the base metal, and monotonously increase as the heat input decreases. No softened zone exists in heat affected zone (HAZ). Compared with the base metal, although the grains of laser weld are much larger, the toughness of the weld metal is higher within a large range of heat input. Furthermore, as the heat input increases, the toughness of the weld metal rises to a maximum value, at which point the percentage of lower bainite is the highest, and then drops.

关键词: Laser welding , null , null , null

Metallurgical and Mechanical Properties of Underwater Laser Welds of Stainless Steel

Xudong ZHANG , Wuzhu CHEN , Eiji ASHIDA , Fukuhisa MATSUDA

材料科学技术（英文）

In this paper, the microstructures and mechanical properties of underwater laser welds of Type 304 stainless steel were investigated. JISY308L type filler wire was used as filler wire during welding. A gas-shielding nozzle was used to form a local dry cavity surrounding the welding zone. The main results are summarized as follows: (1) The shielding condition of the local dry cavity severely affects the oxygen content of the weld, the worst shielding condition leading to the oxygen content of 800×10-6, which largely increases the oxide inclusions and somewhat reduces the ferrite content. (2) The increase of oxygen content reduces the elongation rate and reduction of area in tensile test, but has no influence on the tensile strength. (3) In appropriate shielding condition, the mechanical properties of the underwater laser welds can be as same as that in the air.

关键词: Underwater laser beam welding , null , null , null

Chen系统的状态变量周期性反馈控制

李开明 , 李亚洲 , 冯维贵 , 林长

量子电子学报 doi:10.3969/j.issn.1007-5461.2007.05.014

采用非线性反馈控制,用附加了带参数的正弦项对Chen系统进行了有效的控制.随着参数k的逐渐增大,系统的动力学行为呈现出一系列的变化.数值研究结果表明:随控制参数的增大,驱动信号的强度渐大,混沌系统由混沌运动到周期轨道,最终到一相点.

关键词: 混沌 , Chen系统 , 不动点 , Lyapunov指数 , 反馈控制

SIF expressions for center cracked strip loaded by uniformly distributed stress acting on central portion of crack - Corrections of Chen's results - Response

International Journal of Fracture

关键词:

Ion sputter erosion in metallic glass-A response to "Comment on: Homogeneity of Zr(64.13)Cu(15.75)Ni(10.12)Al(10) bulk metallic glass" by L-Y. Chen, Y-W. Zeng, Q-P. Cao, B-J. Park, Y-M. Chen, K. Hono, U. Vainio, Z-L. Zhang, U. Kaiser, X-D. Wang, and J-Z Jiang J. Mater. Res. 24, 3116 (2009)

Journal of Materials Research

The morphology of the dark and bright regions observed by transmission electron microscopy for the Zr(64.13)Cu(15.75)Ni(10.12)Al(10) bulk metallic glass strongly depends on the ion beam parameters used for ion milling. This indicates that the ion beam could introduce surface fluctuation to metallic glasses during ion milling.

关键词: room-temperature

第27卷B辑作者索引

金属学报

Volu扣ne 27SeriesB1991AUTHOR INDEX CCAO Guanghan(曹光旱)············……6一B科6CAo weijie(曹卫恋)..················……5一B32oCAO Yilin(曹益林)··················……6一B443CHANG Xin(常听)···············……1一B48CHE Guang邻n(车广灿)·············一6一B科0CHEN Erbao(陈二保)···············……6一B410CHEN Jia....

关键词:

基于二氧化碳封存的超临界两相流动的数值研究

高诚 , 胥蕊娜 , 陈黎 , 姜培学

工程热物理学报

格子Boltzmann方法(LBM)在计算复杂结构物理模型时具有独特优势并在模拟两相流动过程中能够高效清晰捕捉相界面.本文介绍了基于Shan-Chen多相模型的格子Boltzmann方法的理论成果以及基于二氧化碳封存的超临界两相流的模拟研究.结果表明,Shan-Chen模型在模拟两相流时符合Laplace定律,且两相层流时的速度分布和相渗曲线均与理论值吻合.二氧化碳封存过程中,较大的注入速率在提高二氧化碳残余俘获量的同时会降低其化学俘获量.

关键词: 二氧化碳封存 , 超临界两相流 , Shan-Chen模型

A molecular dynamics study of the structural change differences between Au-225 and Au-369 clusters on MgO surfaces at low temperature

Chinese Physics B

The differences in structural change between Au-225 and Au-369 clusters with their (111) facets supported on MgO(100) surfaces at 5 K are studied by using molecular-dynamics simulations with the atomic interchange potentials of the Au/MgO interface. The parameters are obtained from the ab initio energies using the Chen-Mobius inversion method. Analyses of the pair distribution functions show that the two Au clusters use different deformation processes to adjust the distances between the interface atoms, owing to the misfit between the atom distances among the clusters and the substrates. The local structural changes are identified by atomic density profiles.

关键词: interfaces;nanostructures;computer modelling and simulation;molecular;dynamics;local-structure changes;mgo(001) surface;au;adsorption;cu;nanoclusters;dimers;models;ag

1998 COMPREHENSIVE TABLE OF CONTENTS

中国腐蚀与防护学报

N。1Atmospheric Corrosivlty for Steels………………………………………………… .LIANG Caideng HO[I i。-tat（6）Caustic Stress Corrosion Cr。king of Alloy 800 Part 2.The Effect of Thiosul执e……………………………………… KONG De-sheng YANG Wu ZHAO Guo-zheng HUANG De.ltL。ZHANG Yu。。he CHEN She。g-bac（13）SERS slid E16CttOCh6iniC81 Stlldy Of Illhibit1Oli M6ch＆tllsth Of ThlollY68 Oil ITOll ID H....

关键词: