H.C.Jiang
,
W.L.Zhang
,
J.P.Zhang
,
W.X.Zhang
,
B.Peng
,
S.Q.Yang
金属学报(英文版)
The influences of plating bath solution PH and current density on coercivity of electroplating CoNdNiMnP permanent magnetic film arrays were studied. The experiment results show that both for solution PH and current density there were the best depositing parameters. Too high and too low plating bath solution PH or current density both result in decreasing of the film array coercivity. When solution PH is 3.5 and current density is 5mA/cm^2, the prepared film array coercivity can reach the maximum.
关键词:
solution PH
,
null
,
null
H.C.Jiang
,
W.L.Zhang
,
J.P.Zhang
,
W.X.Zhang
,
B.Peng
,
S.Q.Yang
金属学报(英文版)
In order to improve the performances of electroplating permanent magnetic films, ncodymium is introduced into the electroplating CoNiMnP permanent magnetic films. The influences of the neodymium content are also investigated by varying NdCl3 plating bath concentration. The neodymium-doped films are analyzed by energy dispersive spectrum (EDS), vibrating sample magnetometer (VSM) and magnetic force microscope (MFM). The experimental results show that high magnetic performances of CoNdNiMnP permanent magnetic films with vertical anisotropy could be fabricated with current density 5mA/crne at room temperature. With the increasing of neodymium contents, the magnetic properties of films were improved. However when neodymium contents exceeded 3.5wt, the magnetic properties of films are not improved any more. The increase of film magnetic properties results from the ferromagnetic-coupling between light rare earth element-neodymium and transition metal element-cobalt.
关键词:
CoNiMnP permanent magnetic film
,
null
,
null
吴历斌
,
黄富强
,
江莞
无机材料学报
doi:10.3724/SP.J.1077.2009.00427
利用结构功能区思想的导电功能区和透光功能区,提出了层状p型Cu/Q透明导体的设计模型. LaCuOTe和Sr3Cu2Sc2O5S2因结构层[Cu2Te2]和[Cu2S2]对应导电功能区、[La2O2]和[Sr3Sc2O5]对应透光功能区,符合模型设计思想,是兼具高导电性和高透光性的透明导体,光谱和电导等验证了模型设计p型透明导体的可行性和正确性. 从功能区角度,改变LaCuOS中导电功能层([Cu2S2]→[Cu2Te2])可显著提高材料导电性(10-3S/cm→100S/cm);替换LaCuOTe中透光功能层([La2O2]→[Sr3Sc2O5])能可控改善材料透光性(2.3eV→3.1eV).
关键词:
p型Cu/Q
,
透明导体
,
导电率
,
层状结构
,
结构功能区
姜奉华
,
徐德龙
硅酸盐通报
doi:10.3969/j.issn.1001-1625.2004.06.006
通过研究Q相与C2S和Q相与C4AF的共存条件,构造Q相-C2S-C4AF水泥系统,对此系统水泥形成条件进行研究.研究表明:Q相与C2S和Q相与C4AF能够共存,可以组成Q相-C2S-C4AF-C12A7水泥系统.在Q相-C2S-C4AF-C12A7水泥系统中,Q相在1270℃开始生成,随着温度的升高,Q相的生成量逐渐增大;采用V2O5对β-C2S具有较好的稳定作用.随着C4AF量的增加,Q相的量也在增加,同时,烧成温度降低.
关键词:
Q相
,
Q相-C2S-C4AF水泥
,
形成条件
,
抗压强度
张曼
,
陈朝轶
,
李军旗
,
赵聪
,
杨夏琼
表面技术
doi:10.16490/j.cnki.issn.1001-3660.2015.08.016
目的：研究在含S2-的铝酸钠溶液中Q235钢的腐蚀行为。方法模拟生产条件配制种分母液,采用盐雾腐蚀实验与SEM和EDS分析技术,结合腐蚀质量损失动力学方程与极化曲线,研究Na2 S质量浓度与时间对Q235钢腐蚀行为的影响。结果腐蚀产物元素主要为O,S,Al,Fe。在铝酸钠溶液中,基体的表面会覆盖一层Al2 O3保护膜,可以阻碍溶液中的硫离子穿透到基体表面,对基体起到一定的保护作用。因此腐蚀初期及低质量浓度下,腐蚀速率缓慢；但随着质量浓度的增加、腐蚀时间的延长,保护膜被破坏,S2-穿过保护膜与基体反应,生成硫化物加速了腐蚀速率；当S2-质量浓度增加到6 g/L,腐蚀时间为9 d时,硫化物被氧化成具有较稳定结构的氧化物,腐蚀被抑制。结论在铝酸钠溶液中,S2-质量浓度及腐蚀时间对腐蚀有一定的促进作用,但当腐蚀时间及S2-质量浓度达到一定值时,腐蚀速率呈现减小的趋势,腐蚀被抑制。
关键词:
铝酸钠溶液
,
Q235
,
Na2 S质量浓度
,
腐蚀时间
,
腐蚀速率
,
极化曲线
李振团
,
邢淑清
,
陆恒昌
,
陈重毅
,
麻永林
兵器材料科学与工程
采用实芯和药芯80％Ar+20％CO2气体保护焊对S620Q厚板桥梁钢进行焊接,研究不同焊接工艺对接头组织和力学性能的影响.结果表明:实芯焊缝的主要组织为针状铁素体(AF)+粒状贝氏体(GB),粗晶区(CGHAZ)主要组织为板条贝氏体(LB)+板条马氏体(ML)+GB;药芯焊缝为GB+少量AF,CGHAZ为ML+GB;两种工艺条件下接头均具有较高的强度,都达到了母材强度的85％以上;采用药芯焊接焊缝的硬度高于实芯焊缝;实芯焊缝中具有较高的AF,冲击值高于药芯焊缝,两者的冲击值在熔合区相差最小,药芯CGHAZ中ML+GB混合组织具有较高的韧性,其CGHAZ冲击值高于实芯.
关键词:
S620Q
,
组织
,
接头强度
,
韧性
