Weimin MAO
,
Heng JIANG
,
Ping YANG
,
Huiping FENG
,
Yongning YU
材料科学技术（英文）
The distribution of microelement Fe, Si, Cu and Mg in the surface layer of aluminum foil annealed at 300℃ and 500℃ were determined by secondary ion mass spectrometer. The corrosion structure produced by electrochemical etching was also observed. It was found that the Mg concentration at external surface was increased exponentially over the fourth degree and promoted by higher annealing temperature, which will increase the number of corrosion pits inside the large grains, and therefore the specific capacity of the foils for electrolytic capacitors. The similar effects of microelement Fe, Si and Cu were not so strong.
关键词:
Electrolytic capacitor
,
null
,
null
,
null
Canying CAI
,
Qibin YANG
,
Hongrong LIU
材料科学技术（英文）
Assuming that the wave function , the Schrodinger equation can be written as . Neglecting the last two terms, an analytical expression of electron dynamical diffraction was derived by Qibin YANG et al. In this paper, the analytical expression is modified by further considering the second-order differential term . When the accelerating voltage is not very high, or the sample is not very thin, the reciprocal vector ɡ is large, the modification of the second-order differential is necessary; otherwise it can be neglected.
关键词:
Electron dynamical diffraction
,
null
中国腐蚀与防护学报
N。1Atmospheric Corrosivlty for Steels………………………………………………… .LIANG Caideng HO[I i。-tat（6）Caustic Stress Corrosion Cr。king of Alloy 800 Part 2.The Effect of Thiosul执e……………………………………… KONG De-sheng YANG Wu ZHAO Guo-zheng HUANG De.ltL。ZHANG Yu。。he CHEN She。g-bac（13）SERS slid E16CttOCh6iniC81 Stlldy Of Illhibit1Oli M6ch＆tllsth Of ThlollY68 Oil ITOll ID H....
关键词:
Journal of Physics-Condensed Matter
This research purposes to investigate the atomic and electronic structures of the Al/TiC(001) interface with lattice misfit using the ab initio pseudopotential approach. A detailed analysis of the relaxed atomic structure reveals that the atoms over the initial unfavourable sites relax to the favourable sites along the lateral plane. The properties of the semicoherent interface can be taken as averages over the different coherent sites. In addition, the interface atoms in relatively favourable regions are dragged near to the interface, while those in unfavourable regions are pushed away from the interface. Therefore, a large war-ping near the interface is made perpendicular to the lateral plane. The calculated adhesions explain the different wetting results from the viewpoint of structural transition. The subsequent analysis of electronic properties demonstrates that adhesions dominate mainly via the strong Al-C covalent bond.
关键词:
first-principles;1st principles;adhesion;surfaces;misfit;1st-principles;wettability;al
X. Q. Yang
,
L. X. Huo
,
Y. F. Zhang and J. X. Yan (School of Material Science and Engineering
,
Tianjin University
,
Tianjin 300072
,
China)
金属学报(英文版)
The buckling formation and influence factors during welding thin - plated structures were investigated based on finite element methods, An engineering treatment method for prdicating the buckling distor- tion was proposed in here. It was used the equivalent applied thermal - load to simulate the welding residual stress,therefore the calculation of complex welding distoriton can be transformed into 3D elas- tic structural applied- load analyses, which can reduce the quantities of calculating works effectively. The validation of the method was verified by comparison of the numerical simulation and experimental results. The simulation of buckling distorition for side - walled structrues of paseenger train was per- formed and the calculation was in agreement with measuring results in general. It was shown that the main factors for producing the buckling were the intermittent fillet and ping the during welding the stiffened beams and columns to the panel.The existence of the free edge of panels would reduce the crit- ical buckling stress and enlarge the deflection obviously,but the continuous weld in closed frames didn' t degrade the buckling situation.
关键词:
welding buckling distortion
,
null
,
null
颜慧成
,
郭征
,
张孟亭
,
张洪平
钢铁研究学报
引入变量m(冲量密度)和Yang-Mills型规范变换m=u+gradφ,将原始变量的N-S方程转化为规范-不变量形式,用自由质点法处理Voronoi元,对连铸结晶器弯月面处保护渣流动行为进行数学模拟.输出振动周期内的动态流场,然后结合一组试验数据进行计算,计算结果与实际情况相吻合,进而讨论了渣圈对液渣流动行为的影响,为研究结晶器弯月面处保护渣的行为和铸坯振痕的形成提供了一定的依据.
关键词:
连续铸钢
,
保护渣
,
流动行为
,
数学模拟
章明川
,
张楚
,
林郁郁
,
徐旭常
工程热物理学报
根据快速流化床的基本流动特性、A 型噎塞和 C 型噎塞的特征与定义,建立了一个统一,自恰的快速床模型一分相共存模型.模型以 A 型噎塞的修正Yang公式为‘本构方程',合理预报了快速床的最小固体流率Gsm,以及在固体流率不变的条件下降低操作气速时床层由A型噎塞向C型噎塞的连续过渡.模型中的稀相有效气流速度函数幂次n为可调参数,根据 C 型噎塞速度预报的Yousfi and Gau公式,初步确定模型参数n=4.
关键词:
快速流态化
,
噎塞速度
,
A 型噎塞
,
C 型噎塞
,
分相共存模型
Z.L. Ding
,
Y.C. Fan
,
H.B. Qi
,
D.L. Ren
,
J.B. Guo and Z.Q. Jiang Shijiazhuang Railway Institute
,
Shijiazhuang 050043
,
China
金属学报(英文版)
The SiC_p/Al-alloy composite front broke rotors designed for SHANGHAI SANTANA cars were prepared by semi-solid stirring+liquid for ping process. The properties of the composite rotors were examined. The composite brake rotors were subjected to dynamometer tests on a SCHENCK broke testing system, referring to TLll0 standard of VOLKSWAGEN Company. The friction coefficient and thermal response during fade testing and the wear performance of the composite rotors were studied as the function of various parameters, such as braking pressures, initial speeds, initial temperatures, torque and decelerations, and compared with that of conventional cast iron rotors. The results showed that the properties of SiC_p,/Al-alloy composite rotors can achieve the requirements of commercial cast iron rotor.s. The results also suggested that the friction coefficients of composite rotors under different broking conditions are within the deviation band specified by the TLll0 standard, and the temperature rise of the composite rotors at the cud of each fade stop is lower than that of the cast iron rotors. The wear resistance of composite rotors was higher than that of cast iron rotors. The friction and wear mechanism are analyzed.
关键词:
SiC_p/Al-alloy composite
,
null
,
null
,
null
钱鹏
,
李兴华
量子电子学报
doi:10.3969/j.issn.1007-5461.2015.06.008
基于量子信道加密原理,结合Ping-Pong协议控制模式和信息模式的概念,提出了一个量子安全直接通信协议.在此协议中,发送者和接收者用n对Bell态作为量子信道,发送者用controlled-Not操作将单粒子纠缠入量子信道,接收者用controlled-Not操作将单粒子与量子信道解纠缠.通信双方依次执行控制模式和信息模式,控制模式检测窃听,信息模式发送秘密信息.控制模式和信息模式均不会对已建立的量子信道造成破坏,因此建立量子信道的过程仅需执行一次,此后通信双方可以反复进行控制模式和信息模式,从而不断进行窃听检测和秘密信息传输.
关键词:
量子光学
,
量子安全直接通信
,
信道加密
,
窃听检测
