F. H.(Sam) Froes
,
C. Suryanarayana
,
and D. Mukhopadhyay (Institute for Materials and Advanced Processes (IMAP)
,
University of Idaho
,
Moscow
,
ID 83844-3026
,
USA)C-G. Li(BlM
,
P.O. Box 81
,
Beijing
,
100095
,
P.R. CHINA)K. Brand(On leave from Institut fur Werkstoffwissenshaft
,
Technische Universitst Dresden
,
07062 Dresden
,
Germany
,
at IMAP)
金属学报(英文版)
Mechanical alloying (MA), a solid-state powder processing method, is a "far from equilibrium" synthesis technique which allows development of novel crystal structures and microstructures, leading to enhanced physical and mechanical properties. The ability to synthesize a variety of alloy phases including supersaturated solid solutions, nanocrystalline structures, amorphous phases and intermetallic compounds themselves is discussed. No extension of solubility using MA has been observed in the intermetallics studied. Nanostructured grains were observed in all compositions. Long time milling generally resulted in amorphous phase formation in large part because of the increase in grain boundary energy/mole with reduced grain size; good agreement with the Miedema model for amorphization was obtained in the Al-Fe system. Generally an anneal was required to form the intermetallic after MA; however,intermetallics with a large negative enthalpy of formation were detected in the MA condition. A study of the hot isostatic pressing of γ-TiAl powders produced by MA demonstrated that full density can be achieved at least 400℃ below the normal temperature required for conventional powder, that is 725℃ or below. Nanometered sized grains (≤100nm)were observed after HIP'ing up to 850℃.
关键词:
: Intermetallics
,
null
,
null
Solid State Communications
Considering the image potential, we calculate the binding energies of a shallow donor impurity placed on the centre of a quantum box using the variational approach. The results we have obtained show that there is a great difference of the effects of image potential between the cases including impurity ion image potential and including the image potentials of impurity ion and electron simultaneously. The results also show that the image potential is important, especially when the dimensions of quantum box become small.
关键词:
well;gaas-ga1-xalxas;states
L. H. Lang
,
D. C. Kang
,
S. H. Zhang
,
Z. R. Wang
,
S. J. Yuan
,
K. B. Nielsen and J. Dancket 1) Department of Materials Engineering
,
Harbin Institute of Technology
,
Harbin 150001
,
China 2) Aalberg University
,
Denmark
金属学报(英文版)
In this paper, the forming features of tapered rectangular box during hydrodynamic deep drawing are studied by means of FEM.The effect rules of square blank corner corner amount on body wrinkling are recognized and corresponding methods are discussed. At last, the results of FEM are verified by experi- ment.
关键词:
sheet metal forming
,
null
,
null
Qunqiang FU
材料科学技术（英）
At first, a series of finite element method (FEM) simulation tests were used to find the critical forming conditions of hot-galvanized sheet steel during the rectangular box drawing processing when constant blank holder forces were applied. According the test results, the reasonable alteration scope of initial variable blank holder force (VBHF) was as 1.9~2.3 T. Then, based on the test productions of blank holder force, 12 typical VBHF curves were applied to perform the simulation tests by the simulation software of DYNAFORM. The simulation test results showed that VBHF had great effects on drawing formability of hot-galvanized sheet steel during the rectangular box drawing. However, the different VBHF curves were applied to control the whole drawing and it would get great different effects. At the same tine, the VBHF had great effects on the maximum thick thinning ratio, but had little effect on the maximum thick incrassation ratio. So, reasonable application of the VBHF would greatly decrease the fractures. When the VBHF profile is taken as curve L, the best effect of drawing formability could be obtained. When curve I is used, contrary effect could be gotten. The other types of curves would cause effects between above two types of VBHF curves. Finally, the actual tests were applied to check the validity of the FEM simulation tests. The results show that the FEM simulation tests are good ways for predicting and optimizing the VBHF.
关键词:
Drawing process
,
变压边力
,
热镀锌钢板
Journal of Alloys and Compounds
The subsolidus phase relations in the system La2O3-B2O3-P2O5 were investigated. The system can be divided into 12 three-phase regions. There are nine binary compounds and one ternary compound in this system. The ternary compound La7O6(BO3)(PO4)(2) has a monoclinic structure, space groups P2(1)/n, with lattice constants a = 7.0172 Angstrom, b = 17.9125 Angstrom, c = 12.6500 Angstrom, beta = 97.516 degrees, V = 1576.39 Angstrom(3), and Z = 4.
关键词:
La2O3-B-3-B2O3-P2O5 system;phase relations;ternary compounds
陈玮
,
姚长江
,
尹周澜
,
刘新红
耐火材料
doi:10.3969/j.issn.1001-1935.2008.04.009
分别对反应前后的p-Al2O3进行XRD及SEM分析,确定反应前后Al2O3的物相及显微结构变化;测定加入添加剂前后浆体温度与时间的关系,从而确定添加剂对p-Al2O3水化速度的影响;测定加入添加剂前后浆体的黏度变化,从而测定出添加剂对p-Al2O3水化过程的影响.结果表明:1)p-Al2O3属于无定形态;2)在没有添加剂的情况下,p-Al2O3的水化速率很快,同时释放出大量热量,水化产物主要是一水软铝石、三水铝石和拜耳石;3)加入碳酸钠及六偏磷酸钠的混合物为添加剂后,p-Al2O3的水化速率显著降低,释放出的热量显著降低,水化产物主要是一水软铝石.
关键词:
p - 氧化铝
,
水化硬化
,
不定形耐火材料
,
结合剂
张广俊
,
龙思远
,
曹凤红
材料导报
对AZ81镁舍金铸锭进行(390±10)℃×15h的固溶处理后,在400℃进行挤压,挤压比为32∶1,研究其组织和力学性能.结果表明,挤压AZ81镁合金具有较细的晶粒组织,第二相Mg17Al12被破碎,其分布变得弥散,个别呈流线分布;挤压AZ81镁合金比铸造AZ81镁合金的力学性能有较大提高,其屈服强度为221.6MPa,抗拉强度为311.5MPa,伸长率为14.2%.其挤压态断口表现出明显的塑性断裂特征.
关键词:
AZ81
,
镁合金
,
挤压
,
微观组织
,
性能
张聪正
,
廖慧敏
,
曾明
,
杨刚
,
刘杨
材料热处理学报
采用自制装置对AZ81镁合金进行压入蠕变实验,通过建立稳态压入蠕变本构模型分析合金的蠕变机制,利用扫描电镜（SEM）和X射线衍射（XRD）等方法研究合金蠕变前后的组织和成分。结果表明：压铸AZ81合金在稳态蠕变阶段的应力指数n为2.08,蠕变激活能QC为87.26 kJ/mol;蠕变诱导β相首先由非连续方式析出,到达一定程度后连续析出;沿晶界析出的β相导致合金抗蠕变性能降低;蠕变温度越高,基体和析出相的晶粒尺寸越大;压铸AZ81合金的压入蠕变机制为晶界扩散主导的位错交滑移运动。
关键词:
压铸AZ81合金
,
压入蠕变
,
激活能
,
应力指数
ZHOU Guanghong
,
DING Hongyan
,
ZHOU Fei
,
ZHANG Yue
钢铁研究学报(英文版)
NiPnano Al2O3 composite coatings were deposited by electroless plating, and their microstructures were observed by SEM (scanning electron microscope). The microhardness and the wear resistance of the NiPnano Al2O3 composite coatings were measured using microhardness tester and blockonring tribometer, respectively, and the comparison with those of NiP coatings or NiPmicro Al2O3 coating was given. The influences of aging temperature on their hardness and wear resistance were analyzed. The results showed that the nano Al2O3 particles were distributed uniformly in the NiPAl2O3 coatings. Among three kinds of NiP based coatings, the hardness and wear resistance of NiPnano Al2O3 coatings were largest, and the maximum values could be obtained at 400 ℃. This indicated that the precipitation of nano Al2O3 particles would improve the hardness and wear resistance of the NiP coatings.
关键词:
composite coating;nano Al2O3;aging treatment;mechanical property
