S.S. Yan
,
J.X. Lou
,
L. Zhang
,
R.Z. Zhang
,
Y.M. Zhang
,
Y.H. Liu
,
L.M. Mei and J. Huang(Department of Physics
,
Shandong University
,
Jinan 250100
,
China)(Department of Environment Engineering
,
Shandong University
,
Jinan 250100
,
China)
金属学报(英文版)
Co/Cu discontinuons multilayers were prepared by rf-sputtering method under high sputtering power and then annealed at various temperutures in a high vacuum. The structural, magnetic and transport properties were strongly influenced by the annealing temperature. The annealed samples obviously became discontinuous multilayers.A maximum magnetoresistance ratio of 5.6% was obtained under a relatively low saturation field of about 400 (103/4π)A/m at the optimum annealing temperature of 450℃. When the annealing temperature was increased, the resistivity decreased, and the coercive force and the saturation field increased. The magnetoresistance ratio also depended on the thickness of Co and Cu layers. The magnetic and transport properties were explained on the basis of the discontinuous multilayered structure.
关键词:
discontinuous multilayers
,
null
,
null
QIAO Lijie LIU Rui XIAO Jimei University of Science and Technology Beijing
,
Beijing
,
China
金属学报(英文版)
The effects of stress components on nucleation sites and propagation directions of stress cor- rosion cracks in brass were investigated with specimens under mode Ⅱ and mode Ⅲ loadings. The results indicated that under mode Ⅱ loading,stress corrosion cracks nucleated on the site with maximum normal stress component and propagated along the plane perpendieular to the maximum normal stress,under mode Ⅲ loading,the stress corrosion crack was not evident on the 45°plane due to the general corrosion in aqueous solution with high NH_4OH concentra- tion,while stress corroded in aqueous solution with low NH_4OH concentration, numerous cracks with spacings of 10—150μm were found on the 45°plane with maximum normal stress and no stress corrosion cracks was observed on the plane with maximum shear stress.
关键词:
stress corrosion cracking
,
null
,
null
,
null
Journal of Materials Research
The morphology of the dark and bright regions observed by transmission electron microscopy for the Zr(64.13)Cu(15.75)Ni(10.12)Al(10) bulk metallic glass strongly depends on the ion beam parameters used for ion milling. This indicates that the ion beam could introduce surface fluctuation to metallic glasses during ion milling.
关键词:
room-temperature
孙银洁
,
胡胜泊
,
李秀涛
宇航材料工艺
doi:10.3969/j.issn.1007-2330.2010.02.027
利用SEM、TEM、XPS、XRD、Raman和元素分析仪分析了M40J和T300的表面化学、物理及微观结构特征.研究发现:M40J含碳量高于T300纤维,而含氮量低于T300纤维,且表面活性基团比T300纤维低;M40J和T300碳纤维表面具有大量沟槽,前者相对长而浅,后者相对短而深;T300纤维端面皮芯结构明显,而M40J端面结构较均匀;M40J的微晶结构及取向性优于T300碳纤维.
关键词:
M40J碳纤维
,
微观结构
,
化学特征
,
物理特征
韩建平
,
秦滢杰
,
高伟
,
刘新东
宇航材料工艺
doi:10.3969/j.issn.1007-2330.2014.05.010
针对卫星构件的不同需求,开发了一种芳香胺固化的环氧树脂BA204.研究了无溶剂及溶剂法成型的M40J/BA204复合材料力学、真空放气性能和管件在模拟温度交变条件下的性能变化情况.结果表明:两种方法制备的复合材料力学性能均能满足卫星构件要求,无溶剂法制备的复合材料力学性能优于溶剂法.采用无溶剂法制备的M40J/BA204复合材料其真空质损率为0.23％,可收集挥发性凝聚物为0.009％;复合材料管件经200次热循环冲击后力学性能变化不大,表明M40J/BA204复合材料具有良好的热稳定性.
关键词:
卫星构件
,
M40J/BA204复合材料
,
纤维缠绕
,
无溶剂法
惠雪梅
,
王晓洁
,
尤丽虹
,
王益
,
全小平
宇航材料工艺
doi:10.3969/j.issn.1007-2330.2006.z1.011
通过地面环境模拟实验,分析了高模碳纤维/环氧树脂改性氰酸酯复合材料(M40J/CE/EP)的表面元素,研究了高真空加热环境下复合材料的真空出气性能和出气气体成分.结果表明,M40J/CE/EP复合材料的表面主要由C、O、N元素构成;经高真空加热后,复合材料的出气气体成分以小分子挥发物和碳氢化合物电离碎片为主,有可能在空间低温条件下冷凝在航天器的敏感器件表面而造成污染;通过真空出气性能实验测得,M40J/CE/EP复合材料的总质量损失(TML)的平均值为0.27%,收集到的可凝挥发物(CVCM)为0,完全达到出气筛选合格的指标要求.
关键词:
氰酸酯树脂
,
复合材料
,
出气
,
X射线光电子能谱
宁波
,
赵宇
,
李波
钢铁研究学报
磁温补偿合金1J30经深低温处理后合金中的部分奥氏体转变为马氏体,致使合金的磁温补偿能力下降.通过调整镍含量,同时添加铬,得到了新型磁温补偿合金1J30M.这种新型磁温补偿合金既具有1J30合金的磁温补偿能力,又具有1J32合金的耐深低温能力.
关键词:
磁温补偿合金
,
深低温
,
马氏体相变
