材料期刊网

MICROSTRUCTURES AND MECHANICAL PROPERTIES OF β-NiA1 CONTAINING α-Fe PRECIPITATES

W.H. Tian , A.L. Fan and M. Nemoto (Department of Materials Physics and Chemistry , University of Science and Technology Beijing , Beijing 100083 , China , Sasebo National College of Technology , Okishin 1-1 , Sasebo 857-1193 , Japan)

金属学报(英文版)

The microstructures of B2-ordered NiA1 containing α-Fe precipitates have been investigated in terms of transmission electron microscopy. Fine precipitation of α-Fe (bcc structure) occurs in NiA1 by aging around 973K. The aging behavior was investigated by microhandness measurements and the temperature dependence of the yield strength of precipitate- comaining B2- ordered NiA1 was investigated by compression tests over the temperature range of 673-1273K. The fine precipitation of α-Fe was found to enhance greatly the low and intermediate temperature yield strength. When the deformation temperature is over 1073K, the strength of precipitate- containing NiA1 was comparable to ternary solid solution hardening NiA1-Fe. Dislocations bypass the particles during deformation and typical Orowan loops were observed surrounding the or-Fe particles after deformation.

关键词: nickel aluminide , null , null , null , null

CORRELATION BETWEEN STRESS COMPONENTS AND STRESS CORROSION CRACKS IN BRASS Lecturer,Department of Materials Physics,University of Science and Technology Beijing,Beijing 100083,China

QIAO Lijie LIU Rui XIAO Jimei University of Science and Technology Beijing , Beijing , China

金属学报(英文版)

The effects of stress components on nucleation sites and propagation directions of stress cor- rosion cracks in brass were investigated with specimens under mode Ⅱ and mode Ⅲ loadings. The results indicated that under mode Ⅱ loading,stress corrosion cracks nucleated on the site with maximum normal stress component and propagated along the plane perpendieular to the maximum normal stress,under mode Ⅲ loading,the stress corrosion crack was not evident on the 45°plane due to the general corrosion in aqueous solution with high NH_4OH concentra- tion,while stress corroded in aqueous solution with low NH_4OH concentration, numerous cracks with spacings of 10—150μm were found on the 45°plane with maximum normal stress and no stress corrosion cracks was observed on the plane with maximum shear stress.

关键词: stress corrosion cracking , null , null , null

CURRENT STATUS OF HIGH-RESOLUTION ELECTRON-MICROSCOPY AND ITS APPLICATIONS TO MATERIALS SCIENCE AND CONDENSED MATTER PHYSICS

材料科学技术（英文）

The present paper summarizes the current status of high resolution elect;on microscopy ( HREM) and the applications of HREM to materials science and condensed matter physics. This review recounts the latest development of high resolution electron microscope, progress of HREM and the applications of HREM, including the crystal structure determination of microcrystalline materials and characterization of the local structure of the defects and nanostructured materials as well as qualitative and quantitative analysis of the grain boundaries, interfaces and interfacial reactions in the advanced materials by means of HREM in combination with electron diffraction, subnanometer level analysis, image simulation and image processing.

关键词: juxtaposed pentagonal antiprisms;two-dimensional quasicrystal;domain;boundary structures;close-packed phases;nanocrystalline materials;crystal-structure;copper oxidation;initial-stage;translational;symmetry;rotational symmetry

Current Status of High Resolution Electron Microscopy and Its Applications to Materials Science and Condensed Matter Physics

Douxing LI and Hengqiang YE (Laboratory of Atomic imaging of Solids , Institute of Metal Research , Chinese Academy of Sciences , Shenyang , 110015 , China)

材料科学技术（英文）

The present paper summarizes the current status of high resolution electron microscopy (HREM)and the applications of HREM to materials science and condensed matter physics. This review recounts the latest development of high resolution electron microscope, progress of HREM and the applications of HREM, including the crystal structure determination of microcrystalline materials and characterization of the local structure of the defects and nanostructured materials as well as qualitative and quantitative analysis of the grain boundaries, interfaces and interfacial reactions in the advanced materials by means of HREM in combination with electron diffraction,subnanometer level analysis, image simulation and image processing.

关键词:

Department of Metallurgy and Materials Engineering of Chongqing University

YAN Guangting Chongqing University , Sichuan , China.

材料科学技术（英文）

关键词:

Deformation at Room and Low Temperatures and Martensite Transformation in Resistance Spot Welding Duplex γ & α(δ) Materials of 301L Stainless Steel

Wei LIU

材料科学技术（英文）

Transformation induced plasticity (TRIP) and twinning induced plasticity (TWIP) effects had been widely studied in single austenite steel. But in duplex γ & α(δ) phase, such as welding materials of stainless steel, they had been less studied. Tensile shear loading experiment of resistance spot welding specimens prepared with 2 mm 301L sheets, was carried out at 15℃ and -50℃. Optical microscopy and scanning electron microscopy (SEM) as well as X-ray diffraction (XRD) were used to investigate the microstructure of weld nugget, and specimens fracture surface. The results showed that the initial weld nugget was composed of 8.4% α(δ) ferrite and 91.6% austenite. Tensile shear load bearing capacity of spot welding specimen at -50℃ was 24.8 kN, 17.7% higher than that at 15℃. About 78.5 vol. pct. martensite transformation was induced by plastic deformation at -50℃, while about 67.9 vol. pct transformation induced at 15℃. The plasticity of spot welding joint decreased with the decline of experimental temperature.

关键词: 301L stainless steel , stainless , steel , Resistance , spot , wel

FeMoB Enhanced Sintering of P/M 316L Stainless Steel

YANG Xia , GUO Shiju

钢铁研究学报(英文版)

Liquidphase enhanced sintering of powder metallurgy (P/M) 316L stainless steel by addition of sintering aids was studied. 2%-8% of prealloyed FeMoB powder with two different particle sizes was added as sintering aids, and the specimens were sintered in vacuum at 1 200-1 350 ℃. The results show that the fine FeMoB powder (5-10 μm) has stronger activated effect. The sintered density increases with the increase in sintering aid content or sintering temperature. Warm compaction has a better effect on the control of dimensional precision of compacts. The prealloyed FeMoB powder deviated from Mo2FeB2 component can also be sintering aid of P/M 316L stainless steel.

关键词: P/M 316L stainless steel;liquidphase sintering;activated sintering;FeMoB;sintering aid

试棒的w_0/l_0值对Zn-5%Al合金超塑性m-δ关系的影响

刘勤 , 裔式珙

材料研究学报

在250℃以■=0.025min~(-1)测到的Zn-5%Al 合金的超塑性m-δ曲线均属式。w_0/l_0值加大使m_0,m_L 和δ_F 值增大,但对δ_L 和m_F 值无大影响。试样厚度的加大(由1增大到2mm)仅使δ_L 和δ_F 值增大,考虑w_0/l_0比值的影响,C_3~((m_0-m_L))-(m_L=m_(mas))型C.L.m-δ方程式规划为:或其中,m′_0(W_0/l_0)=m_0,m′_0>m_0;m′_L(w_0/l_0)=m_L,m′_L>m。w_0/l_0=0.15—0.39。当w_O/l_0=1时,缺口效应消失,δ(或δ_F)值为最大。

关键词: Zn-5%Al合金 , mechanics of superplasticity , C.L.m-δequation

Dependence of strength, elongation, and toughness on grain size in metallic structural materials

Journal of Applied Physics

The dependence of yield strength, uniform elongation, and toughness on grain size in metallic structural materials was discussed. The toughness is defined as the product of yield strength and uniform elongation. The yield strength versus grain size can be well described by the Hall-Petch relation; however, the uniform elongation versus grain size is not well understood yet. A simple model involving the densities of geometrically necessary dislocations and statistically stored dislocations was proposed to estimate the uniform elongation versus grain size. Existing data for low carbon steels and aluminum indicate that, in the grain size less than 1 mu m, the materials usually exhibit high strength and low uniform elongation and, in the grain size greater than 10 mu m, the materials usually exhibit low strength and high elongation; in either case the toughness is low. However, in the grain size of several micrometers, the toughness is the highest. It is suggested that we should pay more attention to develop the metallic materials with grain size of several micrometers for structural applications. (c) 2007 American Institute of Physics.

关键词: nanocrystalline copper;nanostructured metal;steels;deformation;ductility;law

Metal-Free Heterogeneous Catalysis for Sustainable Chemistry

Chemsuschem

The current established catalytic processes used in chemical industries use metals, in many cases precious metals, or metal oxides as catalysts. These are often energy-consuming and not highly selective, wasting resources and producing greenhouse gases. Metal-free heterogeneous catalysis using carbon or carbon nitride is an interesting alternative to some current industrialized chemical processes. Carbon and carbon nitride combine environmental acceptability with inexhaustible resources and allow a favorable management of energy with good thermal conductivity Owing to lower reaction temperatures and increased selectivity, these catalysts could be candidates for green chemistry with low emission and an efficient use of the chemical feedstock This Review highlights some recent promising activities and developments in heterogeneous catalysis using only carbon and carbon nitride as catalysts The state-of-the-art and future challenges of metal-free heterogeneous catalysis are also discussed.

关键词: carbon;catalyst;heterogeneous catalysis;selectivity;sustainable;chemistry;graphitic carbon nitride;modified activated carbon;nanofiber/graphite-felt composite;ordered mesoporous carbons;oxygen;reduction reaction;nitrogen-doped graphite;fuel cell cathode;onion-like carbon;oxidative dehydrogenation;hydrogen-production