The fracture behavior of cold sprayed 304 stainless steel coating in cold rolling process was studied. The 304 stainless steel coatings were deposited on low carbon steel substrate by cold gas dynamic spray (CGDS) and then cold rolled, respectively. The fracture morphology of the coatings was observed and analyzed, and the crack distri- butions along the longitudinal rolling direction of the coatings were also investigated and discussed. The results showed that the cohesive strength of the cold sprayed 304 stainless steel coating was too low to be cold rolled. Mi crocracks were formed in the as-sprayed coatings and ran perpendicularly to the rolling direction. The spacing dis- tance between these cracks decreased with the increase of the cold rolling reduction. In addition, it was also found that the initial crack generated at the surface of the coating and propagated from the surface to the interface along the weakly bonded particles. A theoretical analysis was developed for the coating fracture. It gave a critical minimum cohesive bonding strength of the coating for non-breaking in cold rolling process. The crack propagation manner of the cold rolled coatings was also discussed.
参考文献
| [1] | Hofman R;Vreijling M P W;Ferrari G M et al.Electrochem ieal Methods for Characterization of Thermal Spray Resistant Stainless Steel Coatings[J].Electrochemical Methods in Cor rosion Research VI,1998,289(02):641. |
| [2] | Zeng Z;Sakoda N;Tajiri T .Corrosion Behavior of Wire-Arc-Sprayed Stainless Steel Coating on Mild Steel[J].Journal of Thermal Spray Technology,2006,15(03):431. |
| [3] | K. M. El-Khatib;M. O. AbouHelal;A. A. El-Moneim;H. Tawfik .Corrosion stability of SUS316L HVOF sprayed coatings as lightweight bipolar plate materials in PEM fuel cells[J].Anti-Corrosion Methods and Materials,2004(2):136-142. |
| [4] | Borchers C.;Gartner F.;Stoltenhoff T.;Assadi H.;Kreye H. .Microstructural and macroscopic properties of cold sprayed copper coatings[J].Journal of Applied Physics,2003(12):10064-10070. |
| [5] | l.i W Y;Zhang C;Guo X P et al.Deposition Characteristics of AI 12Si Alloy Coating Fabricated by Cold Spraying With Rel atively 1.arge Powder Particles[J].Applied Surface Science,2007,253(17):7124. |
| [6] | Xian-Jin Ning;Jae-Hoon Jang;Hyung-Jun Kim .The effects of powder properties on in-flight particle velocity and deposition process during low pressure cold spray process[J].Applied Surface Science: A Journal Devoted to the Properties of Interfaces in Relation to the Synthesis and Behaviour of Materials,2007(18):7449-7455. |
| [7] | Guan-Jun Yang;Chang-Jiu Li;Feng Han;Wen-Ya Li;Akira Ohmori .Low Temperature Deposition And Characterization Of Tio_2 Photocatalytic Film Through Cold Spray[J].Applied Surface Science: A Journal Devoted to the Properties of Interfaces in Relation to the Synthesis and Behaviour of Materials,2008(13):3979-3982. |
| [8] | Lee H Y;Yu Y H;Lee Y C et al.Interracial Studies Between Cold-Sprayed WO(3),Y2Oa Films and Si Substrate[J].Ap-plied Surface Science,2004,227(1/2/3/4):244. |
| [9] | Gyuyeol Bae;Yuming Xiong;S. Kumar .General aspects of interface bonding in kinetic sprayed coatings[J].Acta materialia,2008(17):4858-4868. |
| [10] | Na H;Bae G;Shin S et al.Advanced Deposition Character-istics of Kinetic Sprayed Bronze/Diamond Composite by Tai-loring Feedstock Properties[J].Compound Science and Tech-nology,2009,69(3/4):463. |
| [11] | Wen-Ya Li;Hanlin Liao;G. Douchy .Optimal design of a cold spray nozzle by numerical analysis of particle velocity and experimental validation with 316L stainless steel powder[J].Materials & Design,2007(7):2129-2137. |
| [12] | T. Schmidt;F. Gartner;H. Assadi .Development of a generalized parameter window for cold spray deposition[J].Acta materialia,2006(3):729-742. |
| [13] | Sundararajan, G;Phani, PS;Jyothirmayi, A;Gundakaram, RC .The influence of heat treatment on the microstructural, mechanical and corrosion behaviour of cold sprayed SS 316L coatings[J].Journal of Materials Science,2009(9):2320-2326. |
| [14] | J. Vlcek;L. Gimeno;H. Huber;E. Lugscheider .A Systematic Approach to Material Eligibility for the Cold-Spray Process[J].Journal of Thermal Spray Technology,2005(1):125-133. |
| [15] | G. Sundararajan;Naveen M. Chavan;G. Sivakumar;P. Sudharshan Phani .Evaluation of Parameters for Assessment of Inter-Splat Bond Strength in Cold-Sprayed Coatings[J].Journal of Thermal Spray Technology,2010(6):1255-1266. |
| [16] | C. BORCHERS;T. SCHMIDT;F. GAERTNER;H. KREYE .High strain rate deformation microstructures of stainless steel 316L by cold spraying and explosive powder compaction[J].Applied physics, A. Materials science & processing,2008(3):517-526. |
| [17] | Fukanuma H;Ohno N;Sun B;Huang RZ .In-flight particle velocity measurements with DPV-2000 in cold spray[J].Surface & Coatings Technology,2006(5):1935-1941. |
| [18] | Frank Gartner;Thorsten Stoltenhoff;Tobias Schmidt;Heinrich Kreye .The Cold Spray Process and Its Potential for Industrial Applications[J].Journal of Thermal Spray Technology,2006(2):223-232. |
| [19] | H. R. Le;M. P. F. Sutcliffe;P. Z. Wang .Surface oxide fracture in cold aluminium rolling[J].Acta materialia,2004(4):911-920. |
| [20] | Choi H;Yoon S;Uhm S;Lee C .Characterization of the spraying beads deposited by the kinetic spraying process[J].Surface & Coatings Technology,2005(2/3):374-381. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%