通过试验和数值模拟两种方法分析细间距器件SnAgCu焊点的热疲劳寿命.采用-55～125℃温度循环试验,发现SnAgCu焊点疲劳寿命约为1150次.基于Anand方程和Wong方程两种本构模型,针对两类疲劳寿命预测方程进行对比研究.结果显示,基于两种模型计算的SnAgCu焊点应力时间历程曲线具有相类似的趋势,但是应力值有较大差别.针对两类疲劳寿命预测方程,结合试验研究分析焊点的疲劳寿命,基于Wong方程结合双蠕变模型计算的疲劳寿命值和试验结果吻合良好,而基于Anand方程结合Engelmaier修正的Coffin-Mason方程计算的疲劳寿命略高于试验结果.
This paper presents the fatigue life of fine pitch devices with SnAgCu soldered joints calculated by experiments and numerical simulation. Special test vehicles were selected with SnAgCu soldered joints for testing, and thus the fatigue life of the SnAgCu soldered joints was 1150 cycles under -55-125 ℃ test condition. On the other hand finite element code ANSYS was used to simulate the stress-strain response and fatigue life of lead free soldered joints based on two sorts of constitutive models: Anand equation and Wong equation, plus two life prediction models. It is found that the similar tendency can be seen in the stress history course curves based on these constitutive models, and the values of stress based on these constitutive equation are different from each other. Two life prediction equations, comparing with thermal cycling experiments, were employed to analyze the fatigue life of fme pitch devices with SnAgCu soldered joints under thermal cycling test. It is seen that the life calculated by fatigue life prediction equations with two creep mechanism based on Wong model coincide well with that of the test data, and the life calculated by Engelmaier-modified Coffin-Mason equation calculated based on Anand model is slightly higher than that of the actual result.
参考文献
| [1] | Park S B et al.[J].ASME Journal of Electronic Packaging,2007,129(01):28. |
| [2] | Zhang Liang,Xue Songbai,Lu Fangyan,Han Zongjie,Wang Jianxin.Numerical simulation of soldered joints and reliability analysis of PLCC components with J-shape leads[J].中国焊接,2008(02):37-41. |
| [3] | Vandevelde B et al.[J].Microelectronics Reliability,2006,47(2-3):259. |
| [4] | Li M Y et al.[J].ASME Journal of Electronic Packaging,2004,26(01):22. |
| [5] | ZHANG Liang,XUE Songbai,CHEN Yan,HAN Zongjie,WANG Jianxin,YU Shenglin,LU Fangyan.Effects of cerium on Sn-Ag-Cu alloys based on finite element simulation and experiments[J].稀土学报（英文版）,2009(01):138-144. |
| [6] | Xia Y H et al.[J].Journal of Alloys and Compounds,2008,45(1-2):174. |
| [7] | Wiese S et al.[J].Microelectronics Reliability,2007,47(2-3):223. |
| [8] | ZHANG Liang,XUE Songbai,HAN Zongjie,WANG Jianxin,GAO Lili,SHENG Zhong.MECHANICAL PROPERTIES OF FINE PITCH DEVICES SOLDERED JOINTS BASED ON CREEP MODEL[J].机械工程学报（英文版）,2008(06):82-85. |
| [9] | Zhang Liang et al.[J].Journal of Materials Science:Materials in Electronics,2009,20(08):685. |
| [10] | 薛松柏,陈燕,吕晓春,廖永平.稀土元素Ce对锡银铜无铅钎料润湿性及钎缝力学性能的影响[J].焊接学报,2005(10):1-4. |
| [11] | Amagai M et al.[J].Microelectronics Reliability,2002,42(06):951. |
| [12] | Xue Songbai et al.[J].Transactions of Nonferrous Metals Society of China,2005,15(z3):305. |
| [13] | Zhang Liang et al.[J].Journal of Materials Science:Materials in Electronics,2009,20(12):1193. |
| [14] | Qian Z F et al.[J].International Journal of Microcircuits and Electronic Packaging,1999,22(04):288. |
| [15] | Shanggua D K.Lead-Free Solder Interconnect Reliability[M].US:ASM International,2008:150. |
| [16] | Spraul M et al.[J].Microelectronics Reliability,2007,47(2-3):252. |
| [17] | Qi Y et al.[J].IEEE Transactions on Advanced Packaging,2006,29(04):690. |
| [18] | Zhang Q et al.[J].ASME Journal of Electronic Packaging,2005,127(04):415. |
| [19] | Pang J H L et al.[J].ASME Journal of Electronic Packaging,2000,122(03):255. |
| [20] | Jen Y M et al.[J].IEEE Transactions on Components Packaging and Manufacturing Technology,2006,29(04):718. |
| [21] | Zhang Liang et al.[J].Modelling and Simulation in Materials Science and Engineering,2009,17(07):075 014. |
| [22] | 张亮,薛松柏,卢方焱,韩宗杰,禹胜林,赖忠民.基于蠕变模型细间距器件焊点疲劳寿命预测[J].机械工程学报,2009(09):279-284. |
| [23] | Lee S W R et al.[J].Circuit World,1998,24(03):26. |
| [24] | Lee S W R et al.[J].Circuit World,2002,28(02):32. |
| [25] | 马鑫,钱乙余,吉田综仁.表面组装焊点内部应力-应变场的数值模拟（Ⅰ）[J].中国有色金属学报,2000(03):404. |
| [26] | Syed A.[A].Florida:ECTC,2001:255. |
| [27] | Zhang X W et al.[J].International Journal of Microcircuits and Electronic Packaging,2002,25(01):147. |
| [28] | Lau J H et al.[J].ASME Journal of Electronic Packaging,2002,124(03):205. |
| [29] | Chang B J et al.[J].Welding Journal,2006,85(S):63. |
| [30] | 李晓延,王志升.倒装芯片封装结构中SnAgCu焊点热疲劳寿命预测方法研究[J].机械强度,2006(06):893-898. |
| [31] | Cheng Z N et al.[J].Soldering and Surface Mount Technology,2000,12(02):31. |
| [32] | Wang G Z et al.[J].ASME Journal of Electronic Packaging,2001,123(03):247. |
| [33] | 王国忠,程兆年.SnPb钎料合金的粘塑性Anand本构方程[J].应用力学学报,2000(03):133-139. |
| [34] | 褚卫华,陈循,陶俊勇,王考.热循环加载条件下空洞对EBGA焊点可靠性的影响[J].计算力学学报,2005(01):119-123. |
| [35] | 吴玉秀,薛松柏,张玲,黄翔.QFP组件的优化模拟及焊点热疲劳寿命的预测[J].焊接学报,2006(08):99-102. |
| [36] | 佟川,曾声奎,陈云霞.塑封球栅阵列焊点热疲劳寿命预测有限元方法[J].焊接学报,2007(10):89-92. |
| [37] | Syed A.[A].Las Vegas:ECTC,2004:737. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%