The effects of rod falling and moving, external flow field, boiling film and radiation were investigated on fluid flow and heat transfer of AISI 4140 steel horizontal rod during direct quenching by mathematical modeling. The flow field and heat transfer in quenching tank were simulated by computational fluid dynamics （CFD） method considering falling and moving of rods during process. Therefore, modeling of flow field was done by a fixed-mesh method for general moving objects equations, and then, energy equation was solved with a numerical approach so that effeet of boiling film heat flux was considered as a source term in energy equation for solid-liquid boundary. Simulated results were verified by comparing with published and experimental data and there was a good agreement between them. Also, the effects of external forced flow and film boiling were investigated on heat flux output, temperature distribution and heat transfer coefficient of rod. Also simulated results determined optimum quenching time for this process.
参考文献
| [1] | A.H. Meysami;R. Ghasemzadeh;S.H. Seyedein;M.R. Aboutalebi .An investigation on the microstructure and mechanical properties of direct-quenched and tempered AISI 4140 steel[J].Materials & design,2010(3):1570-1575. |
| [2] | Ju D Y;Zhang W M;Zhang Y .Modeling and Experimental Verification of Martensitic Transformation Plastic Behavior in Carbon Steel for Quenching Process[J].Materials Science and Engineering,2006,438- 440:246. |
| [3] | ASM.ASM Metals Handbook.Heat Treating[M].Metals Park:American Society for Metals,1991 |
| [4] | Janez Grum;Slavko Bozic;Martin Zupancic .Influence of quenching process parameters on residual stresses in steel[J].Journal of Materials Processing Technology,2001(1):57-70. |
| [5] | Meysami A H .Optimization of Thermo Mechanical Behavior and Direct Quenching of AISI 4140 Steel Using Physical and Numerical Simulation[D].Tehran:School of Metallurgy and Material Engineering,Iran University of Science and Technol ogy,2010. |
| [6] | Sotudian H R .Simulation of AISI 4140 Steel Bars Hot Rolling[D].Tehran:Faculty of Material Science and Engineering,Iran University of Science and Technology,2009. |
| [7] | Sarmiento G S;Bugna J F;Canale L C F et al.Modeling Quenching Performance by the Kuyucak Method[J].Materi als Science and Engineering,2007,459A(1/2):383. |
| [8] | Kandlikar S G.Handbook of Phase Change:Boiling and Con densation[M].New York:crc Press,1999 |
| [9] | Fukuda K;Shiotsu M;Sakurai A .Effect of Surface Conditions on Transient Critical Heat Fluxes for a Horizontal Cylinder in a Pool of Water at Pressures Due to Exponentially Increasing Heat Inputs[J].Nuclear Engineering and Design,2000,200(1/2):55. |
| [10] | J. Wendelstorf;K. H. Spitzer;R. Wendelstorf .Spray water cooling heat transfer at high temperatures and liquid mass fluxes[J].International Journal of Heat and Mass Transfer,2008(19/20):4902-4910. |
| [11] | Eugene A;Mizikar A .Spray Cooling Investigation for Con- tinuous Casting of Billets and Blooms[J].Iron and Steel Engineer,1970,47(01):53. |
| [12] | Liu C;Theofanous T G.Film Boiling on Spheres in Single- and Two Phase Flows.Part 1 :Experimental Studies ANS Proceedings,Part 2:A Theoretical Study[A].Portland,Oregon,USA,1995:233. |
| [13] | Jacobi H;Kaestle G;Wunnenberg K .Heat Transfer in Cy- clic Secondary Cooling During Solidification of Steel[J].Iron- making and Steelmaking,1984,11(03):132. |
| [14] | Mudawar I;Valentine W S .Determination of the Local Quench Curve for Spray-Cooled Metallic Surfaces[J].Journal of nalof Heat Treating,1989,7(02):107. |
| [15] | Mohammadi M .Optimum Conditions for Achieving of Good Mechanical Properties of Quench and Tempered AISI 4140 Steel[D].Shiraz:Faculty of Material Science and Engineer- ing,Shiraz University,2007. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%