提出了半固态连铸的主要工艺参数设计原则: 浇注温度为浇入制浆室后的熔体温度恰好等于液相线的温度; 制浆室预热温度保证熔体浇入后, 其界面温度不小于停止流动的临界温度, 不大于熔体的初始温度; 开拉时间在保证开拉时引锭不滑脱的前提下越短越好; 拉坯速度既保证金属熔体通过制浆室的时间不小于非技晶球状组织的形成时间, 又要保证熔体在通过结晶器的时间内能够形成不小于安全厚度的凝固层.
参考文献
| [1] | Flemings M C .Behavior of metal alloys in the semisolid state[J].Metallurgical and Materials Transactions,1991,22(03):269. |
| [2] | 邢书明 .难变形钢铁材料半固态连铸技术研究[D].北京科技大学,1996. |
| [3] | Kenneth E. BLAZEK;James E. KELLY;Narayan S. POTTORE .The Development of a Continuous Rheocaster for Ferrous and High Melting Point Alloys[J].ISIJ International,1995(6):813-818. |
| [4] | Blazek K .The improvement of surface quality of continu- ous rheocast bar of steel and high melting point alloys[J].ISIJ International,1997,37(04):365-374. |
| [5] | 邢书明,李亚敏,马静,陈维视,翟启杰,胡汉起,杨秀斌,杨日增,贺丽荣,杨天增.半固态连铸过程拉漏（断）机理研究[J].特种铸造及有色合金,2000(01):16-19. |
| [6] | 蔡开科.连续铸钢[M].北京:冶金工业出版社,1990:105. |
| [7] | Prasad P R;Ray S;Gaindher J L et al.Relation between processing,microstructure and mechanical properties of rheocast Al-Cu alloys[J].Journal of Materials Science,1988,23:823-829. |
| [8] | 邢书明;李亚敏;胡汉起 et al.半固态铝硅合金非枝晶固相的形成与演变[J].中国有色金属学报,1999,9(09):270-274. |
| [9] | Taha M A;Mahallawy-N A EL .Control of the continu-ous rheocasting process.Part I,Heat flow model[J].Journal of Materials Science,1998,23:1379-1384. |
| [10] | 邢书明,曾大本,胡汉起,翟启杰,马静,李亚敏.半固态连铸过程的滞留层尺寸预测[J].中国有色金属学报,2000(06):800. |
| [11] | Kapranas P .Semi-solid metal processing an environmen- tally friendly process[J].Materials World,1994,8:465-467. |
| [12] | Taha M A .Control of the continuous rheocasting process.Part 2:Rheological behavior analysis[J].Journal of Materials Science,1998,23:1385-1390. |
| [13] | Molenear J M M .Analysis of process limits for continu-ous thixotropic slurry casting[J].Journal of Materials Science,1985,20:700-709. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%