为了研究变形程度对强变形Al-4%Cu合金退火行为的影响,通过透射电镜观察和拉伸试验,研究了人工时效Al-4%Cu合金经过不同变形量的多向压缩变形(MAC),退火(120 ℃/60 min)后的显微组织和力学性能.研究表明:试样中的第二相在MAC过程中破碎溶回基体后,会在后续退火过程中再次析出,且析出相回溶的程度对退火组织性能的影响很大.含θ"相试样和含θ'相试样经MAC变形后,析出相完全回溶于基体,在退火过程中有新的第二相析出,试样强度升高;同时试样的的塑性也得到了提高,这与再析出粒子对超细晶粒长大的阻碍作用有关.析出相未完全回溶的含θ相试样,退火后强度低于退火前,析出相回溶和再析出交替进行.析出相基本回溶态强韧化效果最佳.
参考文献
| [1] | Ruslan Z. Valiev;Terence G. Langdon .Principles of equal-channel angular pressing as a processing tool for grain refinement[J].Progress in materials science,2006(7):881-981. |
| [2] | J. Cizek;I. Prochazka;B. Smola;I. Stulikova;R. Kuzel;Z. Matej;V. Cherkaska;R.K. Islamgaliev;O. Kulyasova .Microstructure and thermal stability of ultra fine grained Mg-based alloys prepared by high-pressure torsion[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2007(1-2):121-126. |
| [3] | Kwan, C;Wang, ZR;Kang, SB .Mechanical behavior and microstructural evolution upon annealing of the accumulative roll-bonding (ARB) processed Al alloy 1100[J].Materials Science & Engineering. A, Structural Materials: Properties, Microstructure and Processing,2008(1-2):148-159. |
| [4] | Langdon TG .The processing of ultrafine-grained materials through the application of severe plastic deformation[J].Journal of Materials Science,2007(10):3388-3397. |
| [5] | Ruslan Z. Valiev;Yuri Estrin;Zenji Horita .Producing Bulk Ultrafine-Grained Materials by Severe Plastic Deformation[J].JOM,2006(4):33-39. |
| [6] | Nong Gao;Marco J. Starink;Minoru Furukawa .Evolution of Microstructure and Precipitation in Heat-Treatable Aluminium Alloys during ECA Pressing and Subsequent Heat Treatment[J].Materials Science Forum,2006(0):275-280. |
| [7] | M. MURAYAMA;Z. HORITA;K. HONO .MICROSTRUCTURE OF TWO-PHASE Al-1.7 at/100 Cu ALLOY DEFORMED BY EQUAL-CHANNEL ANGULAR PRESSING[J].Acta materialia,2001(1):21-29. |
| [8] | L. S. Vasil'ev;I. L. Lomaev;E. P. Elsukov .On the Analysis of the Mechanisms of the Strain-Induced Dissolution of Phases in Metals[J].The Physics of Metals and Metallography,2006(2):186-197. |
| [9] | 许晓嫦,刘志义,党朋,于文斌,宁爱林.强塑性变形下Al-Cu合金不同析出相的回溶及性能变化[J].材料导报,2006(z2):463-465,472. |
| [10] | XU Xiao-chang,LIU Zhi-yi,LI Yun-tao,DANG Peng,ZENG Su-min.Evolution of precipitates of Al-Cu alloy during equal-channel angular pressing at room temperature[J].中国有色金属学会会刊（英文版）,2008(05):1047-1052. |
| [11] | 党朋,许晓嫦,刘志义,于文斌,宁爱林,曾苏民.铝合金等径角挤压和多向压缩变形中析出相的回溶研究[J].材料热处理学报,2007(05):82-85. |
| [12] | 许晓嫦 .强变形诱导铝合金析出相低温回溶现象及应用基础研究[D].中南大学,2008. |
| [13] | 胡楠,许晓嫦,张孜昭,屈啸.强变形诱导析出相回溶对Al-Cu合金力学性能的影响[J].中国有色金属学报,2010(10):1922-1931. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%