选取NHZP-1型双马树脂拉挤Z—pin，并结合差示扫描量热法（DSC）测定及工艺参数优化来调控其固化度，将Z—pin按70°角（Z—pin植入方向与水平方向夹角）植入Rohacell-51WF泡沫、采用5429／HT7双马单向预浸料作为蒙皮，成功制备K-cor夹层结构，并展开了相应的力学性能测试。根据Z-pin在K-cor与X-cor夹层中与蒙皮结合方式差异建立微观拉伸结构简图，并借助欧拉杆屈曲模型来估算其临界失稳载荷，定性分析了平面压缩过程中Z-pin的破坏模式与增强机制。结果表明：Z-pin固化度为62．74％时，K-cor夹层结构的平面拉伸强度和模量分别为1．55MPa与88．56MPa，平面压缩强度和模量高达3．61MPa与128．84MPa，均比空白泡沫试样和具有相同Z-pin参数的X-cor夹层结构有所提高。
K-cor structure was successfully fabricated by inserting angle 70° Z-pin in Rohacell- 51WF foam, using NHZP- 1 and 5429/HT7 bismaleimides as pultrusion resin and preimpregnated medium, respectively. The corresponding investigation on mechanical tests were carried out. A structural model based on different binding styles between Z-pin and panel in K-and X-cot was established. In order to qualitatively describe the failure mode and strengthening mechanism, the critical stress of Z- pin in the compressive test was evaluated and compared by using Euler column buckling modes. The experimental results show that 62.74 % curing degree of Z-pin in K-cor structure can make tensile strength and modulus reach 1.55 MPa and 88.56 MPa as well as 3.61 MPa and 128.84 MPa, respectively, in the compressive test, which is much higher than that of X-cor structure and blank foam matrix.
参考文献
| [1] | 张纪奎,邴正能,寇长河.大展弦比复合材料机翼结构设计研究[J].航空学报,2005, 26(4): 450-453. |
| [2] | 杜龙.X-cor夹层复合材料力学性能研究[D].西安:西北工业大学,2007. |
| [3] | 杜龙,矫桂琼,黄涛.Z-pin增强泡沫夹层结构面压缩性能研究[J].航空材料学报,2008,28(4): 101-106. |
| [4] | Mouritz A P. Tensile fatigue properties of 3D composites withthrough- thickness [J]. Composites Science and Technology,2008,68(12): 2503-2510. |
| [5] | Cartie D D,Fleck N A. The effect of pin reinforcement uponthe through - thickness compressive strength of foam - coredsandwich panels [J]. Composites Science and Technology,2003, 63(16): 2401-2409. |
| [6] | 杜龙,矫桂琼,黄涛,等.X状Z-pin增强泡沫夹层结构的剪切性能[J].复合材料学报,2007,24(6): 140-146. |
| [7] | 李勇,肖军,谭永刚,等.X-coi夹层结构剪切模量实验与分析研究[J].南京航空航天大学学报,2008,40(6): 831-835. |
| [8] | Marasco A I. Analysis and evaluation of mechanical permanceof reinforced sandwich structures: X-Cor. and K-Cor. [D].London: Cranfield University, 2005. |
| [9] | 李勇,肖军,谭永刚,等.BMI-QC130双马树脂拉挤工艺[J].复合材料学报,2009, 26(5); 20-26. |
| [10] | 陈继荣,王井岗,焦扬声.改性双马来酰亚胺树脂的固化工艺研究[J].玻璃钢/复合材料,1998(3): 7-9. |
| [11] | 原永虎.玻璃纤维制备X-cor夹层结构及性能研究[D],南京:南京航空航天大学,2009. |
| [12] | Thien S. Effects of angled stitch reinforcement on foam coressandwich structures [D]. Salt Lake City: Utah University. 2010. |
| [13] | 李勇,肖军,原永虎,等.X-cor夹层结构的平拉性能[J].宇航材料工艺,2010(1): 86-89,. |
| [14] | 中国国家标准化管理委员会.GB/T1453 -2005夹层结构或芯子平压性能试验方法[S].北京:中国标准出版社,2005. |
| [15] | 党旭丹,张红松,王新莉,等.X-cor夹层结构的力学性能试验研究[J].材料导报,2011,25(5): 54-57. |
| [16] | Cartie DDR, Troulis M, Partridge I K. Delamination of Z-pinned carbon fibre reinforced laminates [J]. CompositesScience and Technology, 2006, 6(66) ; 855-861. |
| [17] | 郝继军,张佐光,李敏,等.X-cor夹层复合材料平压性能分析[J].航空学报,2008, 29(4): 1079-1083. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%