Online Shape Dynamic Wrapping Angle Compensation Model of Cold Strip

钢铁研究学报(英文版), 2011, 18(7): 28-32.

Online Shape Dynamic Wrapping Angle Compensation Model of Cold Strip

^1, , ^2, , ^3,

1.National Engieering Research Center for Equipment and Technology of Cold Rolling Strip, State Key Laboratory ofMetastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004, Hebei, China

2.National Engieering Research Center for Equipment and Technology of Cold Rolling Strip, State Key Laboratory ofMetastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004, Hebei, China

3.National Engieering Research Center for Equipment and Technology of Cold Rolling Strip, State Key Laboratory ofMetastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004, Hebei, China

基金项目: National Science and Technology Support Plan of China(2007BAF02BI0) Natural Science Foundation of Hebei Province of China(E2011203004)

关键词：冷轧带钢 , 形状检测 , 补偿模式 , 包角 , 在线 , BP神经网络 , 动态变化 , 面形检测

Online Shape Dynamic Wrapping Angle Compensation Model of Cold Strip

Keywords： cold roiling strip shape detecting , wrapping angle , compensation , shape meter , cold mill ,

In specific condition, when wrapping angle of cold rolling strip covering surface of shape detecting roll dynamically changes, online radial compression of the shape detecting roll is changed too, and it seriously affects online shape detecting precision of cold strip. Based on the latest intelligent shape meter developed by Yanshan University, using PSO-BP neural network and actual working condition datum, the cold strip online dynamic wrapping angle compensation model is established, and successfully applied in 1250 mm 6-high cold mill, remarkable results are achieved. The error between calculated values and measured values of total tensions is within 3 %

参考文献

[1]	LIAN Jia-chuang;LIU Hong-min.Control of Strip Thickness and Shape[M].Beijing= Enginery Industry Publishing Compa ny,1996
[2]	WANG Jun sheng;BAI Jin lan;LIU Xiang-hua.Theory and Process Control of Cold Strip Rolling[M].北京:科学出版社,2009
[3]	XU Le-jiang.Shape Control and Mill Type Selection of Cold Mill Strip[M].Beijing= Metallurgical Industry Press,2007
[4]	LIN Zhen bo;DUAN Zhen yong;LIAN Jia chuang et al.Analysis on Shape Standard Curve of Cold Roiling Mill and Its Selection[J].Journal of Iron and Steel Research,1997,9(03):55.
[5]	白剑,张清东,常铁柱,李有元,许健勇.1420冷连轧机组第1机架板形控制目标曲线研究[J].钢铁,2007(10):56-59.
[6]	郑志刚,李欣伟,程其华,陈杰,倪国华,白振华.1220五机架冷连轧机板形曲线的改进[J].上海金属,2008(04):55-58.
[7]	刘宏民,丁开荣,李兴东,江光彪.板形标准曲线的理论计算方法[J].机械工程学报,2008(08):137-142.
[8]	于丙强,杨利坡,刘宏民,彭艳,尤磊.冷轧带钢接触式板形仪研制及其工业应用[J].仪器仪表学报,2010(04):904-911.
[9]	YU Bing-qiang;SUN Ya bo;LIU Hong min et al.Compen- Sation Model for Shape Measuring of Cold Strip Roiling [J] Journal of Iron and Steel Research[J].International,2010,17(06):21.
[10]	LIU Hong min;YANG Li po;YU Bing qiang et al.Entire Inlayed Block Intelligence Type Shape Meter= China[P].CN101694368A,2010-04-07.

上一张下一张

上一张下一张

计量

下载量()
访问量()

作者相关

在本站搜索
在百度学术搜索
在万方数据库搜索
在CNKI搜索

文章评分

您的评分：
1

0%
2

0%
3

0%
4

0%
5

0%