非调质钢F40MnV三辊楔横轧的实验研究

材料热处理学报, 2012, 33(7): 67-71.

非调质钢F40MnV三辊楔横轧的实验研究

王敏婷 ^1, , 李学通 ^2, , 彭进 ^3, , 杜凤山 ^4,

1.燕山大学机械工程学院,河北秦皇岛066004

2.燕山大学机械工程学院,河北秦皇岛066004

3.燕山大学机械工程学院,河北秦皇岛066004

4.燕山大学机械工程学院,河北秦皇岛066004 亚稳材料制备技术与科学国家重点实验室,河北秦皇岛066004

基金项目: 河北省自然科学青年基金(E2012203028) 国家自然科学基金(50705080)

关键词：楔横轧 , 非调质钢 , 空心轴 , 冷却 , 性能

Experimental study on three-roll cross-wedge rolling of non-quenched and tempered steel F40MnV

Keywords： cross-wedge rolling , non-quenched and tempered steel , hollow axle , cooling , property

针对非调质钢F40MnV空心轴类件楔横轧成形问题，为获得最佳轧制与冷却工艺制度，在三辊楔横轧机上开展了轧制与冷却实验研究。利用正交法制定实验过程工艺参数，并将带有热电偶的试件进行轧制。轧后采用水冷，水冷加空冷，风冷，空冷4种方式进行冷却，得到相应的温度变化曲线。基于实验结果，采用金相分析和性能实验手段研究了温度、断面减缩率和冷却介质对F40MnV钢轧后冷态力学性能的影响。结果表明采用水冷加空冷、断面减缩率35％、轧制温度为950℃时的成形工艺可得到较为优良的力学性能

Aiming at the forming technology of cross-wedge rolled hollow shaft of F40MnV steel, the experimental study on rolling and cooling of steel F40MnV was carried on three-roll cross-wedge rolling mill in order to optimize the process of rolling and cooling. Based on orthogonal test results, the processing parameters for experiment were determined and rolling of the workpieces with thermocouple was carried out. After rolling, four cooling ways, namely water cooling, air cooling plus water cooling, wind cooling and air cooling, were applied to cool the deformed workpieces, and the corresponding temperature changes were measured. The influence of rolling temperature, reduction of area and cooling modes on microstructure and mechanical properties of the rolled steel F40MnV were investigated. The results show that good mechanical properties are obtained for the steel F40MnV rolled at temperature of 950 ℃ with reduction of area of 35% and then cooled by air cooling plus water cooling.

参考文献

[1]	胡正寰;张康生;王宝雨.楔横轧零件成形技术与模拟仿真[M].北京:冶金工业出版社,2005
[2]	Fu X P;Dean T A .Past developments,current applications and trends in the cross wedge roiling process[J].International Journal of Machine Tools and Manufacture,1993,33(03):367-400.
[3]	Z. Pater .Finite element analysis of cross wedge rolling[J].Journal of Materials Processing Technology,2006(2):201-208.
[4]	S. Urankar;M. Lovell;C. Morrow .Development of a critical friction model for cross wedge rolling hollow shafts[J].Journal of Materials Processing Technology,2006(1/3):539-544.
[5]	Shu Xuedao;Li Chuanmin;Zhao Jing;Hu Zhenghuan .Theoretical and experimental study of varying rule of rolling-moment about cross-wedge rolling[J].Journal of Materials Processing Technology,2007(0):752-756.
[6]	丁韡,杨翠苹,张康生,胡正寰.楔横轧等内径空心轴的热力耦合数值模拟[J].北京科技大学学报,2010(04):525-529.
[7]	董成瑞;任海鹏.微合金非调质钢[M].北京:冶金工业出版社,2000
[8]	徐善义;路之坦.热锻用40MnV,(Ti)非调质钢[J].一拖科技,1991(01):14-21.
[9]	Minting WANG;Xuetong LI;Fengshan DU .Current Trends in Cross Wedge Rolling for Part Forming[J].ISIJ International,2005(11):1521-1525.
[10]	高宏彦.正交及回归试验设计方法[M].北京:冶金工业出版社,1988

上一张下一张

计量

下载量()
访问量()

作者相关

文章评分

您的评分：
1

0%
2

0%
3

0%
4

0%
5

0%

材料期刊网