对树脂传递模塑(RTM)成型的复合材料T型接头进行了工艺参数优化、制备及力学性能实验研究.应用流动模拟软件,对RTM成型的复合材料T型接头进行了基体流动数值模拟,确定模具最佳注射方式和出胶口位置,并优化了影响树脂充模时间的工艺参数,显著提高了RTM接头的工艺性能.根据优化工艺参数结果,制备了RTM成型的复合材料T型接头试样,并进行了拉伸和压缩试验,分析了其破坏机制.根据拉伸和压缩试验现象和结果,发现RTM成型的复合材料T型接头拉伸破坏模式主要为富树脂三角区的树脂与纤维布界面分层,其拉伸破坏主要取决于树脂基体抗剥离分层的拉伸强度;压缩破坏模式为底板中央部位的弯曲分层与折断,其压缩破坏由接头底板中的纤维布抗拉强度决定;T型接头的压缩破坏强度高于拉伸破坏强度.
参考文献
| [1] | Shenoi R A.Violette F L M.A study of structural composite Tee joints in small boats[J].Journal of Composite Materials,1990,24:644-666. |
| [2] | Shenoi R A,Read P,Jackson C L.Influence of joint geometry and load regimes on sandwich Tee joint behaviour[J].Journal of Reinforced Plastic and Composites,1998,17(8):725-740. |
| [3] | Marcadon V,Nadot Y,Roy A,Gacougnolle J L.Fatigue behaviour of T-joints for marine applications[J].International Journal of Adhesion & Adhesives,2006,26:481-489. |
| [4] | Theotokoglou E E.Strength of composite T-joints under pull-out loads[J].Journal of Reinforced Plastic and Composites,1997,16(6):503-518. |
| [5] | Theotokoglou E E.Study of the numerical fracture mechanics analysis of composite T-joints[J].Journal of Reinforced Plastic and Composites,1999,18(3):215-223. |
| [6] | Kumari S,Sinha P K.Finite element analysis of composite wing T-joints[J].Journal of Reinforced Plastic and Composites,2002,21(17):1561-1585. |
| [7] | Apalak M K.On the non-linear elastic stresses in an adhesively bonded T-joint with double support[J].J Adhesion Sci Technol,2002,16(4),459-491. |
| [8] | Apalak M K,Gunes R,Turaman M O,Ceri A A.Thermal and geometrically non-linear stress analyses of an adhesively bonded composite Tee joint[J].Composites Part A,2003,34:135-150. |
| [9] | Kumari S,Sinha P K.Effects of transverse stitching and hygrothermal environment on composite wing T-joints[J].Journal of Reinforced Plastic and Composites,2003,22(18):1705-1728. |
| [10] | Toftegaard H,Lystrup A.Design and test of lightweight sandwich T-joint for naval ships[J].Composites Part A,2005,36:1055-1065. |
| [11] | Theotokoglou E E,Moan T.Experimental and numerical study of composite T-joints[J].Journal of Composite Materials,1996,30(2),190-209. |
| [12] | Stickler P B,Ramulu M.Investigation of mechanical behavior of transverse stitched T-joints with PR520 resin in flexure and tension[J].Composite Structures,2001,52:307-314. |
| [13] | Earl J S,Dulieu-Barton J M,Shenoi R A.Determination of hygrothermal ageing effects in sandwich construction joints using thermoelastic stress analysis[J].Composites Science and Technology,2003,63:211-223. |
| [14] | 邱婧婧,段跃新,梁志勇.RTM工艺参数对树脂充模过程影响的模拟与实验研究[J].复合材料学报,2004,21(6),70-74.Qiu Jingjing,Duan Yuexin.Liang Zhiyong.Computer simulation and actual experiments of RTM mold-filling process affected by processing parameters[J].Acta Materiae Compositae Sinica,2004,21(6):70-74. |
| [15] | 姚福军,段跃新,肇研.RTM工艺树脂注射温度优化[J].复合材料学报,2007,24(3):105-108.Yao Fujun,Duan Yuexin,Zhao Yan.Optimization of resin injection temperature for RTM process[J].Acta Materiae Compositae Sinica,2007,24(3):105-108. |
| [16] | 吴晓青,李嘉禄.基于单向流动研究三维编织预制件的渗透型[J].复合材料学报,2007,24(3):116-120.Wu Xiaoqing,Li Jialu.Permeability of the 3D braided preform based on the unidirectional flow measurement[J].Acta Materiae Compositae Sinica,2007,24(3):116-120. |
| [17] | 戴福洪,张博明,杜善义,武湛君.复杂形状三维薄壁构件RTM制造工艺注模过程模拟[J].复合材料学报,2004,21(2):87-91.Dai Fuhong,Zhang Boming,Du Shanyi,Wu Zhanjun.Simulation of mould-filling in RTM process for 3D complex shape thin shell parts[J].Acta Materiae Compositae Sinica,2004,21(2):87-91. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%