研究了不同挤压速度挤压出的Mg-3.0Nd-0.2Zn-0.4Zr(质量分数,％,NZ30K)镁合金显微组织和室温力学性能.采用光学显微镜观察了合金的显微组织,采用材料拉伸试验测试了合金的室温力学性能,并利用扫描电子显微镜观察了拉伸试样的断口形貌和断口附近的显微组织.结果表明:当挤压速度相对较低时,发生部分再结晶,组织不均匀,合金的强度很高,而塑性则较差;当挤压速度较高时,合金发生了完全动态再结晶,组织均匀,再结晶晶粒明显长大,合金强度降低,而伸长率则明显提高.合理控制挤压速度可获得细小均匀的组织和良好的综合力学性能.
参考文献
| [1] | 胡红军,张丁非,杨明波.镁合金新型复合挤压的有限元和实验研究[J].材料热处理学报,2012(10):149-154. |
| [2] | Xiaobo Zhang;Zhangzhong Wang;Guangyin Yuan .Improvement of mechanical properties and corrosion resistance of biodegradable Mg-Nd-Zn-Zr alloys by double extrusion[J].Materials Science & Engineering, B. Solid-State Materials for Advanced Technology,2012(13):1113-1119. |
| [3] | 徐春杰,郭学锋,刘礼,张忠明.往复挤压快速凝固Mg92.5Zn6.4Y1.1镁合金及其微观结构[J].材料热处理学报,2007(05):96-100. |
| [4] | Xiaobo Zhang;Guangyin Yuan;Zhangzhong Wang.Mechanical properties and biocorrosion resistance of Mg-Nd-Zn-Zr alloy improved by cyclic extrusion and compression[J].Materials Letters,2012:128-131. |
| [5] | 陈彬,林栋樑,曾小勤,卢晨,彭颖红.挤压和等通道角挤压制备高强度Mg97Y2Zn1镁合金[J].中国有色金属学报,2010(04):613-619. |
| [6] | Xu, S.W.;Zheng, M.Y.;Kamado, S.;Wu, K..The microstructural evolution and superplastic behavior at low temperatures of Mg-5.00Zn-0.92Y-0.16Zr (wt.%) alloys after hot extrusion and ECAP process[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2012:60-68. |
| [7] | 郭言炎,林志埙,蒋海燕,吴国华.挤压工艺对ME20M镁合金组织和力学性能的影响[J].中国有色金属学报,2011(01):58-65. |
| [8] | 刘莹,王炳德,王忠堂.挤压变形对镁合金组织与力学性能的影响[J].材料热处理学报,2011(05):51-54. |
| [9] | Xiaobo Zhang;Guangyin Yuan;Lin Mao;Jialin Niu;Penghuai Fu;Wenjiang Ding.Effects of extrusion and heat treatment on the mechanical properties and biocorrosion behaviors of a Mg-Nd-Zn-Zr alloy.[J].Journal of the mechanical behavior of biomedical materials,2012:77-86. |
| [10] | B.P. Zhang;L. Geng;L.J. Huang;X.X. Zhang;C.C. Dong .Enhanced mechanical properties in fine-grained Mg–1.0Zn–0.5Ca alloys prepared by extrusion at different temperatures[J].Scripta materialia,2010(10):1024-1027. |
| [11] | LI Da-quan,WANG Qu-dong,DING Wen-jiang,J.J.BLANDIN,M.SU(E)RY.Influence of extrusion temperature on microstructure and mechanical properties of Mg-4Y-4Sm-0.5Zr alloy[J].中国有色金属学报（英文版）,2010(07):1311-1315. |
| [12] | Zhang X;Yuan G;Wang Z.Effects of extrusion ratio on microstructure,mechanical and corrosion properties of biodegradable Mg-Nd-Zn-Zr alloy[J].Materials Science and Technology,2012 |
| [13] | Tielei Zhang;Zesheng Ji;Shuyan Wu .Effect of extrusion ratio on mechanical and corrosion properties of AZ31B alloys prepared by a solid recycling process[J].Materials & design,2011(5):2742-2748. |
| [14] | Weiqin Tang;Shiyao Huang;Shaorui Zhang;Dayong Li;Yinghong Peng .Influence of extrusion parameters on grain size and texture distributions of AZ31 alloy[J].Journal of Materials Processing Technology,2011(7):1203-1209. |
| [15] | Xiaobo Zhang;Guangyin Yuan;Lin Mao;Jialin Niu;Wenjiang Ding .Biocorrosion properties of as-extruded Mg-Nd-Zn-Zr alloy compared with commercial AZ31 and WE43 alloys[J].Materials Letters,2012(1):209-211. |
| [16] | Fu P;Peng L;Jiang H et al.Effects of heat treatments on the microstructures and mechanical properties of Mg-3Nd-Z 2Zn-0.4Zr alloy[J].Materials Science and Engineering A,2008,486(1-2):183-192. |
| [17] | 卢立伟,刘天模,陈勇,吕城龄.AZ31镁合金挤压长条晶粒的形成机理与消除方法[J].材料热处理学报,2011(12):17-22. |
| [18] | M.A. Azeem;A. Tewari;S. Mishra .Development of novel grain morphology during hot extrusion of magnesium AZ21 alloy[J].Acta materialia,2010(5):1495-1502. |
| [19] | Xu, S.W.;Zheng, M.Y.;Kamado, S.;Wu, K.;Wang, G.J.;Lv, X.Y. .Dynamic microstructural changes during hot extrusion and mechanical properties of a Mg-5.0 Zn-0.9 Y-0.16 Zr (wt.%) alloy[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2011(12):4055-4067. |
| [20] | 宋波,辛仁龙,刘庆.析出相对镁合金变形机理影响的研究进展[J].中国有色金属学报,2011(11):2719-2731. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%