针对某钢厂板坯连铸结晶器及浸入式水口(SEN)的结构参数,建立了描述结晶器内钢液流动的三维数学模型,应用FLUENT软件对结晶器内钢液的流场和温度场进行耦合计算,分析SEN底部形状对结晶器内流场和温度场的影响,并利用水模试验对钢液的流动行为进行了验证.结果表明:凸底水口出口附近钢液的速度较大,流股的冲击深度较大,使结晶器内高温区下移,不利于凝固坯壳的生长;平底水口自由面速度较大、温度较高,有利于保护渣的熔化,但易产生液面裸露现象;凹底自由面速度较小、温度较低,有利于液面稳定.
Based on the structure parameters of mold and submerged entry nozzle,i, e SEN, for slab continuous cast-ing in some steel plant, a 3-D numerical model describing the flow of liquid steel in mold was carried out. Commer-cial software FLUENT was used to simulate coupling flow field and temperature field of the molten steel. The effects of bottom structure of SEN on the flow field and temperature field of molten steel were analyzed and com-pared, moreover, the flow field results were validated by the water model. The research results indicate that near the outlet of convex SEN, the molten steel velocity is relatively high and the impact depth is deep, which enable high temperature region to shift down and go against the growth of solidified shell, the free surface velocity and tempera-ture of flat bottom SEN is relatively high, which is beneficial for mold flux melting but can lead to naked molten steel, the free surface velocity and temperature of concave SEN velocity is relatively low, which is beneficial for the liquid level stabilizing. These research results can be used for the design of SEN as reference.
参考文献
| [1] | Huang X;Thomas B G;Najjar F M .Modeling Superheat Removal During Continuous Casting of Steel Slabs[J].Metallurgical and Materials Transactions B:Process Metallurgy and Materials Processing Science,1992,23B:339. |
| [2] | Thomas B G;Mika L J;Najjar F M .Simulation of Fluid Flow Inside Continuous Slab-Casting Machine[J].Metallurgical and Materials Transactions B:Process Metallurgy and Materials Processing Science,1990,21B:387. |
| [3] | HUA BAI;BRIAN G. THOMAS .Turbulent Flow of Liquid Steel and Argon Bubbles in Slide-Gate Tundish Nozzles: Part I. Model Development and Validation[J].Metallurgical and Materials Transactions, A. Physical Metallurgy and Materials Science,2001(2):253-267. |
| [4] | HUA BAI;BRIAN G.THOMAS .Turbulent Flow of Liquid Steel and Argon Bubbles in Slide-Gate Tundish Nozzles: Part II. Effect of Operation Conditions and Nozzle Design[J].Metallurgical and Materials Transactions, A. Physical Metallurgy and Materials Science,2001(2):269-284. |
| [5] | 王永胜,顾武安,王新华,王万军.板坯连铸水口内钢液流动的数值模拟[J].钢铁研究学报,2008(08):16-20. |
| [6] | 包燕平,张涛,蒋伟,徐保美.板坯连铸结晶器内钢液流场的三维数学模型[J].北京科技大学学报,2001(02):106-110. |
| [7] | 文光华;李刚;张建春 等.高速板坯连铸结晶器内流场、温度场的数值模拟[J].重大自然学报,1997,20(11):23. |
| [8] | Flint P J.A Three-Dimensional Finite Difference Model of Heat Transfer Fluid Flow and Solidification in the Continuous Slab Caster[A].,1992:279. |
| [9] | 张乔英,王书桓,王立涛,李福民,闫小平,杨学书.浸入式水口底部结构对板坯结晶器内钢液流场和温度场的影响[J].钢铁研究,2005(01):17-20. |
| [10] | 朱苗勇;刘家奇;萧泽强 等.板坯连铸结晶器内钢液流动过程的模拟仿真[J].钢铁,1996,30(08):23. |
| [11] | Yang Hongliang;Zhao Liangang;Zhang Xingzhong et al.Mathematical Simulation on Coupled Flow,Heat,and Solute Transport in Slab Continuous Casting Process[J].Metallurgical and Materials Transactions B:Process Metallurgy and Materials Processing Science,1997,29B:1345. |
| [12] | Tsukamoto N .Improvement of Submerges Nozzle Design Based on Water Model Examination of Tundish Slide Gate[J].Steelmaking Conference Proceedings,1991,74(07):803. |
| [13] | 万晓光,韩传基,蔡开科,杨素波,严学模,顾武安.连铸板坯结晶器浸入式水口试验研究[J].钢铁,2000(09):20-23. |
| [14] | 何矿年,肖寄光,韦耀环,孙彦辉,廖卫团.宽板坯连铸结晶器SEN结构和操作参数优化试验研究[J].钢铁,2008(01):26-29,36. |
| [15] | Sung Woo LEE;Moon Ho SUH .A Numerical and Experimental Study of Fluid Flow in Continuous Casting Mold[J].Korean Journal of Chem Eng,1988,5(01):60. |
| [16] | Nguyen A V;Evans G M .Computational Fluid Dynamics Modeling of Gas Jets Impinging Onto Liquid Pools[J].Applied Mathematical Modelling,2006,30:1472. |
| [17] | Brian G. THOMAS;Quan YUAN;Sivaraj SIVARAMAKRISHNAN .Comparison of Four Methods to Evaluate Fluid Velocities in a Continuous Slab Casting Mold[J].ISIJ International,2001(10):1262-1271. |
| [18] | 王翠娜,温良英,陈登福,彭政,张健,靳星,张大江.板坯连铸结晶器内流场的数值模拟[J].过程工程学报,2009(z1):325-328. |
| [19] | 孙蓟泉;李惹剑;马世麟 .结晶器冷却强度与坯壳厚度的关系[J].钢铁,1997,32(02):24. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%