Effect of Processing Parameters on Microstructures of Melt-Spun Al-In Immiscible Alloys

材料科学技术（英文）, 2002, 18(5): 407-410.

^1, , ^2, , ^3, , ^4, , ^5,

1.School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, China

2.School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, China

3.School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, China

4.School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, China

5.School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, China

基金项目: the American Emerson Electric Co.for the financial support

Effect of Processing Parameters on Microstructures of Melt-Spun Al-In Immiscible Alloys

Keywords： Al-In immiscible alloy

Melt spinning rapid solidification technique was employed to fabricate homogeneous Al-In immiscible alloys and theirfinal microstructures and morphologies were investigated. There existed a transition of columnar Al grain→ equiaxedgrain for the thicker ribbon, but only columnar Al grain for the thinner ribbon throughout the thickness. In thecolumnar grain field, most of the fine In particles was distributed within the cells, but a minority of bigger In particlesor short rods was perpendicularly distributed at the grain boundaries. In the equiaxed grain field, the fine In particleswere located in Al grains and coarser particles were situated at the boundaries. The average particle size increasedwith increasing distance from the chilled surface throughout the ribbon. At the same wheel speed (same coolingrate), the average particle size increased with raising In content. At the same composition condition, the averageparticle size decreased with increasing wheel speed and/or decreasing ejection temperature.

参考文献

[1]	H U Walter;B Feuerbacher;H Hamacher;R J Naumann.Materials Science in Space[J].Berlin:Springer-Verlag,1986:343.
[2]	Compiling group of electrical engineering handbook.Electrical Engineering Handbook[M].Shanghai Science and TechnologyPress, Shanghai,1994
[3]	H Fujii;T Kimura;H Kitaguchi;H Kumakura , K Togano .[J].Journal of Materials Science,1995,30:3429.
[4]	S mohan;V Agarwala;R Ray .[J].Materials Science and Engineering,1991,144A:215.
[5]	S Yang .Study on Directionally Solidified Microstructure of AlBi Monotectic Alloy[D].Master thesis of Harbin Institute of Technology(in Chinese),1993.
[6]	Liu Honglingand Jie Xiaoning .[J].Powder Metall Technol(in Chinese),1990,8(01):39.
[7]	R Goswami;K Chattopadhyay .[J].Materials Science and Engineering,1994,179A-180A:163.
[8]	Aiping XIAN;Xiumu ZHANG;Zhongyu LI Acta .[J].Acta Metallurgica Sinica(in Chinese),1996,32(02):113.
[9]	D L Zhang;B Cantor .[J].Philosophical Magazine,1990,62A(05):557.
[10]	L Ratke .[J].Advances in Space Research,1988,8(12):7.

上一张下一张

计量

下载量()
访问量()

作者相关

在本站搜索
在百度学术搜索
在万方数据库搜索
在CNKI搜索

文章评分

您的评分：
1

0%
2

0%
3

0%
4

0%
5

0%

材料期刊网

Effect of Processing Parameters on Microstructures of Melt-Spun Al-In Immiscible Alloys

参考文献