为了精确描述气体辅助充填成型中气体穿透推进过程,研究各工艺参数对成型结果的影响,本文基于气体穿透机理的研究分析,将三明治成型理论应用于气辅成型.以矩形平板型腔为例,结合Hele-Shaw流动模型,建立了气辅充填成型首次气体充填过程的压力控制方程和气/液交界面运动方程,对其应用有限元进行数值模拟.对气辅成型气体穿透过程及其基本规律和各工艺参数对成型结果的影响进行了分析和讨论.箅例结果表明:三明治成型理论应用于气辅成型所建数学模型能较好地揭示气体穿透推进过程的基本特征,并可作为气辅成型过程与实验手段相辅相成的研究工具.
参考文献
| [1] | 陈静波,申长雨,李倩,刘春太.塑料注射成型新工艺[J].工程塑料应用,2002(02):50-53. |
| [2] | Poslinskin A J;Oehler P R;Stokes V K .Isothermal gas-assisted displacement of viscoplastic liquids in tubes[J].Polymer Engineering and Science,1995,35:877-892. |
| [3] | Kamilsli F;Ryan M E .Perturbation method in gas-assisted power-law fluid displacement in a circular tube and a rectangular channe[J].Chemical Engineering Journal,1999,75:167-176. |
| [4] | Ro T S;Homsy G M .Viscoelastic free surface flows:thin film hydrodynamics of Hele-Shaw and dip coating flows[J].Journal of Non-Newtonian Fluid Mechanics,1995,57:203-225. |
| [5] | Turng LS .Development and application of CAE technology for the gas-assisted injection molding process[J].Advances in Polymer Technology,1995,14(01) |
| [6] | Li CT;Isayev AI .Interface evolution and penetration behavior during two-component transfer modeling[J].Polymer Engineering and Science,2004,44(04):688-691. |
| [7] | 陈旭;王立霞;申长雨 等.数值模拟技术在气体辅助充填成型中的应用[J].郑州工业大学学报,1998,19(01):10-17. |
| [8] | Shen CY;Zhai M .An improved algorithm for the simulation of injection-molding filling process[J].Journal of Reinforced Plastics and Composites,2005(7):691-698. |
| [9] | 魏常武,柳和生,周国发,孙懋.过程参数对气辅成型的影响[J].橡塑技术与装备,2003(02):1-5. |
| [10] | 辛勇,阮雪榆,何成宏,柳和生,杨国泰.气辅注射成型中气体穿透下的聚合物熔体壁厚的形成[J].高分子材料科学与工程,2003(03):63-67. |
| [11] | 柳和生,孙燕萍,揭小平.矩形薄腔中聚合物熔体非等温注气充填的数值模拟[J].塑料,2004(01):89-92,81. |
| [12] | 周持兴;俞炜.聚合物加工理论[M].北京:科学出版社,2004:45-472. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%