利用电热线爆定向喷涂方法在45钢基体上制备了stellite/WC复合涂层,运用扫描电镜及能谱分析对复合涂层的形貌、微观结构以及涂层的基体结合机理进行了分析,利用纳米硬度计测量了复合涂层的硬度和弹性模量.结果表明:涂层致密,无层状结构出现;喷涂过程中涂层颗粒在基体上的快速凝固使得涂层晶粒细小均匀,晶粒为200～500 nm;涂层与基体界面发生了元素扩散现象,为扩散-冶金结合;涂层硬度的最大值为18.6 GPa,模量的最大值为310 GPa,硬度和模量沿横截面都呈现先增加而后减小的变化趋势.
参考文献
| [1] | 陈华辉 .等离子喷涂WC-Co涂层的磨料磨损[J].金属热处理,1997,22(11):5-8. |
| [2] | Kathruia Y P;Tsuboi A.[J].Micropolis:SPIE,1996:86-92. |
| [3] | Yamamoto M;Tazaki K;Ogawa R et al.Development of wire explosion sprayed coating of cylinder bore[J].Kawasaki Technical Review,2000,145:42-45. |
| [4] | Tamura H;Konoue M;Sawaoka A B .Zirconium boride and tantalum carbide coating sprayed by electrothermal explosion of powders[J].Journal of Thermal Spray Technology,1997,6(04):463-468. |
| [5] | 刘宗德,杨昆,段鹏,蒲泽林.线爆炸法制备WC-Co硬质合金涂层的实验研究[J].爆炸与冲击,2003(02):116-121. |
| [6] | 薛文斌,王超,李永良,陈如意.纯钛表面微弧氧化膜纳米压入法研究[J].材料科学与工艺,2002(02):113-116. |
| [7] | J.He;M.Ice .Synthesis of nanostructured WC-12 pct Co coating using mechanical milling and high velocity oxygen fuel thermal spraying[J].Metallurgical and Materials Transactions, A. Physical Metallurgy and Materials Science,2000(2):541-553. |
| [8] | 薛文斌,邓志威,陈如意,张通和.LY12铝合金微弧氧化陶瓷膜的纳米压入研究[J].稀有金属材料与工程,2001(04):281-285. |
| [9] | Pharr G M .Measurement of mechanical properties by ultra-low load indentation[J].Materials Science and Engineering,1998,A253(1-2):151-159. |
| [10] | 胡明;张延华;车成卫 .爆炸喷射沉积WC-Co涂层组织及显微硬度分析[J].材料科学与工艺,1997,5(01):103-106. |
| [11] | 张玉娟,孙晓峰,金涛,韩松,段绪海,赵乃仁,管恒荣,胡壮麒.爆炸喷涂NiCrAlTaY涂层的微观组织分析[J].金属学报,2003(02):185-188. |
| [12] | Sobolev V V;Guilemany J M;Nutting J.Analysis of different mechanisms of coating-substrate adhesion in thermal spraying[A].Ohilo, USA: ASM International Material Park,1997:797-803. |
| [13] | 范群波,王鲁,王富耻.等离子喷涂金属/陶瓷颗粒的瞬态碰撞压力研究[J].北京理工大学学报,2003(02):168-171,193. |
| [14] | Sobolev V V;Guilemany J M;Miguel J R et al.Investigation of the development of coating structure during high velocity oxy-fuel (HVOF) spraying of WC-Ni powder particles[J].Surface and Coatings Technology,1996,82:114-120. |
| [15] | 蒲泽林,杨昆,刘宗德,毛雪平.电热爆喷涂层温度场的数值模拟[J].中国表面工程,2004(01):20-23. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%