本文对搭接长度分别为15mm,20mm,23mm,37ram,60mm的Z-pins增强陶瓷基复合材料接头在单向载荷作用下的连接性能进行了试验研究和数值模拟.试验结果表明接头的最终失效形式有两种:(1)搭接长度大于、等于20mm的接头由搭接板断裂而失效;(2)搭接长度等于15mm的接头由搭接面的脱胶而失效.在搭接长度为20mm～60mm之间,接头的最大破坏载荷与搭接长度之间呈线性关系变化.采用有限元的方法对搭接接头的破坏过程进行了数值模拟,模拟结果与试验结果吻合较好,进而得到了介于上述两种破坏模式之间的搭接接头的搭接长度.
参考文献
| [1] | 刘(韦华),矫桂琼,管国阳,常岩军.Z-pin增强陶瓷基复合材料拉伸和层间剪切性能[J].复合材料学报,2007(01):86-90. |
| [2] | Larry W. Byrd;Victor Birman .Effectiveness of z-pins in preventing delamination of co-cured composite joints on the example of a double cantilever test[J].Composites, Part B. Engineering,2006(4/5):365-378. |
| [3] | P. CHANG;A.P. MOURITZ;B.N. COX .Properties and failure mechanisms of pinned composite lap joints in monotonic and cyclic tension[J].Composites science and technology,2006(13):2163-2176. |
| [4] | James G.Ratcliffe;T.Kevin O'Brien .Discrete Spring Model for Predicting Delamination Growth in Z-Fiber Reinforced DCB Specimens[NASA/TM-2004-213019][R].Hampton,Virginia:NASA,2004. |
| [5] | J.D.Cowley .Joining of Ceramic-Matrix Composites[J].American Ceramic Society Bulletin,1989,68(09):1619-1623. |
| [6] | Abd-El-Naby SFM.Load distribution in two-pinned polymer composites joints[M].Amsterdam:Elsevier Science,1991:553-574. |
| [7] | Dano ML et al.Stress and failure analysis of mechanical fastened joints in composite laminates[J].Computers & Structures,2000,50(03):287-296. |
| [8] | Bulent Murat Icten;Ramazan Karakuzu .Progressive failure analysis of pin-loaded carbon-epoxy woven composite plates[J].Composites science and technology,2002(9):1259-1271. |
| [9] | HKS,ABAQUS,user's manual.Version 6,5-1[M]. |
| [10] | 王波 .三维编织复合材料力学行为研究[D].西北工业大学,2003. |
| [11] | 孔宪仁,黄玉东,范洪涛,孙文训.细编穿刺C/C复合材料不同层次界面剪切强度的测试分析[J].复合材料学报,2001(02):57-60. |
| [12] | 贾成厂.陶瓷基复合材料导论[M].北京:冶金工业出版社,2002:7-5024-2910-7,124-150. |
| [13] | 张增光 .2D-C/SiC复合材料的弹性常数预测及失效模式研究[D].西北工业大学,2005. |
| [14] | 汪清 .C/SiC复合材料连接接头应力与破坏形式数值分析[D].西北工业大学,2005. |
| [15] | 薛克兴;周瑾.复合材料结构连接件设计与强度[M].北京:航空工业出版社,1988:12. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%