运用商业软件Ansys-Fluent,建立了1t钢包底吹氩与合金熔化扩散数值模型,其中钢包吹氩模型通过Wood'sMetal物理试验验证,吻合很好.研究采用数值模拟与现场试验相结合的方法分析了钢包内流场与合金加入的位置及方式对合金在钢包内扩散的影响.结果表明:260L/min吹氩流量过大,且吹氩时间过长(120s),建议使用100 L/min的吹氩流量,加合金前吹氩时间30s,使Al块熔化与混均,保护合金,加合金后吹氩30s,降低合金的烧损.合金采用加入棒固定,在吹氩口上方加入后保持3～5 s,熔化时间能由6.2s降低至2.0s,混匀时间能由35s降低至23s.另外,在降低烧损的同时,减少吹氩量和温降,起到节能减排的作用.
参考文献
| [1] | 倪冰,狄瞻霞,罗志国,邹宗树.底吹氩钢包内钢液流动和混合数值模拟的应用[J].炼钢,2008(04):40-42,51. |
| [2] | Woo J S,Szekely J,Castillejos A H,et al .A Study on the Mathematical Modeling of Turbulent Recirculating Flows in Gas-Stirred Ladies[J].Metall Trans,1990,21(2):269.,1990. |
| [3] | Wei J H,Zeng L .Numberical Simulation of Fluid Flow in Bath During Combined Top and Bottom Blowing VOD Refining Process of Stainless Steel[J].Steel Res Int,2012,83(11):1053.,2012. |
| [4] | Li B K,Yin H B,Zhou C Q .Modeling of Three-Phase Flows and Behavior of Slag/Steel Interface in an Argon Gas Stirred Ladle[J].ISIJ Int,2008,48(12):1704.,2008. |
| [5] | Turkoglu H,Farouk B .Mixing Time and Liquid Circulation Rate in Steelmaking Ladles With Vertical Gas Injection[J].ISIJ Int,1991,31(12):1371.,1991. |
| [6] | Zhang L F,Taniguchi S J,Cai K K,et al .Fluid Flow Bahaviour of Liquid in Cylindrical Vessels Stirred by One or Wwo Air Jets[J].Journal of University of Science and Technology Beijing,2000,7(3):170.,2000. |
| [7] | Liu H P .,Qi Z Y,Xu M G.Numberical Simulation of Fluid Flow and Interfacial Behavior in Three-Phase Argon-Stirred Ladles With One Plug and Dual Plugs[J].Steel Res Int,2011,82(4):440.,2011. |
| [8] | Jun A,Thomas B G,Peter J .Experimental and Theoretical Investigation of Mixing in a Bottom Gas-Stirred Ladle[J].Urbana,2004,51(1):61801.,2004. |
| [9] | Johansen S T,Boysan F .Fluid Dynamics in Bubble Stirred Ladles:Part Ⅱ.Mathematical Modeling[J].Metallurgical and Materials Transactions,1988,19(10):755.,1988. |
| [10] | Zhang L F .Mathematical Simulation of Fluid Flow in GasStirred Liquid Systems[J].Modelling and Simulation in Materials Science and Engineering,2000,8(4):463.,2000. |
| [11] | Kuo J T,Wallis G B .Flow of Bubbles Through Nozzles[J].International Journal of Multiphase Flow,1988,14(5):547.,1988. |
| [12] | Xie Y,Oeters F .Experimental Studies on the Flow Velocity of Molten Metals in a Ladle Model at Centric Gas Blowing[J].Steel Res Int,1992,63(3):93.,1992. |
| [13] | Jun A,Zhang L F,Thomas B G .Modeling of Inclusion Removal in Ladle Refining[J].Urbana,2005,51(1):61801.,2005. |
| [14] | Zhang L Y .Modelling on Melting of Sponge Iron Particles in Iron-Bath[J].Steel Res Int,1996,67(11):466.,1996. |
| [15] | Zhang L Y,Oeters F .Mathematical Modeling of Alloy Melting in Steel Melts[J].Steel Res Int,1999,70:128.,1999. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%