采用金相、扫描电镜(SEM)和焊接热模拟方法,研究了不同峰值温度和焊接线能量对ASTM4130钢焊接热影响区(HAZ)显微组织、冲击韧性和断口形貌的影响.结果表明,ASTM4130钢热影响区除回火软化区外均发生脆化现象.当峰值温度为1200 ℃和1350℃时,由于晶粒粗大,且产生了贝氏体、未回火马氏体和M-A组元等非平衡组织,其冲击韧性损失达母材的94.5%,脆化现象最严重.当峰值温度为950℃,冲击韧性较低的原因是该区产生了未回火马氏体和块状铁素体.当峰值温度为800℃时,晶界附近碳化物聚集和不均匀分布,以及块状铁素体的存在,造成该区发生脆化.焊态下焊接线能量对ASTM4130钢粗晶区的冲击韧性影响较小.
参考文献
[1] | 刘海霞.深海半潜式钻井平台的发展[J].船舶,2007(03):6-10. |
[2] | 李国荣,Li Guorong.我国深水石油钻采装备现状及发展建议[J].石油机械,2009(08):87-91. |
[3] | J. R. Still .Welding of AISI 4130 and 4140 steels for drilling systems: the ability to withstand high pressures puts these steels in high demand for use in offshore oil and gas drilling[J].Welding Journal,1997(6):37-42. |
[4] | G. SPANOS;R.W. FONDA;R.A. VANDERMEER .Microstructural Changes in HSLA-100 Steel Thermally Cycled to Simulate the Heat-Affected Zone During Welding[J].Metallurgical and Materials Transactions, A. Physical Metallurgy and Materials Science,1995(12):3277-3293. |
[5] | 胡丽华,张雷,许立宁,路民旭.Cr含量对低合金耐蚀管线钢焊接接头组织和性能的影响[J].材料热处理学报,2010(03):92-96. |
[6] | 付瑞东,逯允海,杨永强,张文辉.2.25Cr-1Mo-0.25V耐热钢焊接热影响区热模拟试验研究[J].材料热处理学报,2007(01):66-70,74. |
[7] | A. Lambert-Perlade;A.F. Gourgues;A. Pineau .Austenite to bainite phase transformation in the heat-affected zone of a high strength low alloy steel[J].Acta materialia,2004(8):2337-2348. |
[8] | 康煜平.金属固态相变及应用[M].北京:化学工业出版社,2007:98. |
[9] | Bonnevie E;Ferriere G;Ikhlef A;Kaplan D;Orain JM .Morphological aspects of martensite-austenite constituents in intercritical and coarse grain heat affected zones of structural steels[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2004(1/2):352-358. |
[10] | 王学,常建伟,黄关政,任遥遥.WB36钢多层焊接头近缝区网状组织研究(Ⅱ):显微结构及韧性[J].材料热处理学报,2009(02):76-80. |
[11] | 邹增大;李亚江;尹士科.低合金调质高强度钢焊接及工程应用[M].北京:化学工业出版社,1999:66. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分:
-
10%
-
20%
-
30%
-
40%
-
50%