对Mo和Al 2 O 3/Mo纳米粉末进行模压成形，研究纯Mo和Al 2 O 3/Mo压坯在1700~2000℃温度范围内的等温烧结过程，并结合烧结模型分析材料烧结过程中的动力学；利用SEM和TEM分析复合材料的显微组织。结果表明：压坯密度与Al2O3的加入量有关，高温烧结时Al2O3/Mo复合材料的致密度高于纯Mo的致密度；在Al2O3/Mo复合材料烧结过程中，烧结机制既有体积扩散又有晶界扩散，且随着Al2O3含量的增加，晶界扩散趋势明显；纯Mo和Al 2 O 3体积分数为5%、10%和15%Al 2 O 3/Mo复合材料的烧结激活能分别为254.24、234.04、221.40和164.37 kJ/mol；Al 2 O 3的加入可促进晶粒的均匀化和组织的细化。
By molding formation, the isothermal sintering processes of pure Mo and Al 2 O 3/Mo green compact were investigated in the temperature range of 1 700?2 000℃. And combined with sintering model, the sintering kinetics was studied. The microstructures of the composites were analyzed by SEM and TEM. The results show that the green compact density and the adding amount of Al 2 O 3 are related, and the composite density is higher than that of pure Mo in high temperature sintering process. During Al 2 O 3/Mo composite sintering process, the sintering mechanism is proved to contain volume diffusion and grain boundary diffusion, and with the increase of Al 2 O 3 content, the latter trend is obvious. The sintering activation energies of pure Mo and Al 2 O 3 composites with volume fractions of 5%, 10% and 15% are 254.24, 234.04, 221.40 and 164.37 kJ/mol, respectively. The addition of Al 2 O 3 can promote the uniformity and refining for the grains.
参考文献
| [1] | 王东辉,袁晓波,李中奎,郑欣,张军良,张清,白润.钼及钼合金研究与应用进展[J].稀有金属快报,2006(12):1-7. |
| [2] | NAWA M;SEKINO T;NIIHARA K .Fabrication and mechanical behaviour of Al 2 O 3/Mo nano-composites[J].Journal of Materials Science,1994,29(12):3185-3192. |
| [3] | SBAIZERO O;PEZZOTTI G;NISHIDA T .Fracture energy and R-curve behavior of Mo/Al 2O3 composites[J].ACTA MATERIALIA,1998,46(02):681-687. |
| [4] | 余大江,常春,刘俊涛,姜江.Mo/Al2O3复合材料的耐磨性[J].摩擦学学报,2009(05):442-446. |
| [5] | 果世驹.粉末烧结理论[M].北京:冶金工业出版社,1998:1-10. |
| [6] | MAJUMDAR S;RAVEENDRA S;SAMAJDAR I;BHARGAVA P SHARMA I G .Densification and grain growth during isothermal sintering of Mo and mechanically alloyed Mo-TZM[J].Acta Materialia,2009,57:4158-4168. |
| [7] | GBT 3850-1983.致密烧结金属材料与硬质合金密度测定方法[S]. |
| [8] | 王盘鑫.粉末冶金学[M].北京:冶金工业出版社,1997:188-214. |
| [9] | 赵虎,杨秦莉,庄飞,刘仁智,张常乐,刘俊怀.纯钼烧结规律研究[J].中国钼业,2011(06):53-56. |
| [10] | 黄培云.粉末冶金原理[M].北京:冶金工业出版社,2004:265-338. |
| [11] | 王零森,杨义斌,张金生,樊毅,吴芳.掺碳碳化硼活化烧结及其动力学[J].中国有色金属学报,2000(01):37-42. |
| [12] | LANGE R G;MUNIR Z A;HOLT J B .Sintering kinetics of pure and doped boron carbide[J].Mater Sci Res,1989,13:311-321. |
| [13] | Koji Matsui;Akira Matsumoto;Masato Uehara .Sintering Kinetics at Isothermal Shrinkage: Effect of Specific Surface Area on the Initial Sintering Stage of Fine Zirconia Powder[J].Journal of the American Ceramic Society,2007(1):44-49. |
| [14] | Luis A. Perez-Maqueda;Jose Manuel Criado;Concepcion Real .Kinetics of the Initial Stage of Sintering from Shrinkage Data: Simultaneous Determination of Activation Energy and Kinetic Model from a Single Nonisothermal Experiment[J].Journal of the American Ceramic Society,2002(4):763-768. |
| [15] | SATO E;CARRY C .Effect of powder granulometry and pretreatment on sintering behavior of submicron-grained-alumina[J].Journal of the European Ceramic Society,1995,15:9-16. |
| [16] | Fang TT.;Shiue JT.;Shiau FS. .On the evaluation of the activation energy of sintering[J].Materials Chemistry and Physics,2003(1):108-113. |
| [17] | Hirai S.;Saitou Y.;Nishimura T.;Uemura Y.;Mitomo H. Brewer L.;Shimakage K. .Synthesis and sintering of cerium(III) sulfide powders[J].Journal of the American Ceramic Society,1998(1):145-151. |
| [18] | Bernard-Granger G;Guizard C .Apparent activation energy for the densification of a commercially available granulated zirconia powder[J].Journal of the American Ceramic Society,2007(4):1246-1250. |
| [19] | Lee WJ.;Fang TT. .Effect of the strontium : barium ratio and atmosphere on the sintering behavior of strontium barium niobate[J].Journal of the American Ceramic Society,1998(2):300-304. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%